CTC Union GSW-3208M Скачать руководство пользователя страница 59

Страница: 59 / 148

Chapter 6. Manage / Configure the Switch

switchport

command

This command is used to configure some switch function characteristics for the interface port(s).

(config-if)# switchport ?

acceptable-frame-types Specifies frame type

allowed Configures the VLAN port list

mode Configures the port mode

native

Configures the PVID of the port

private-vlan Private VLAN

untag-vid Configures the port untag vid

vlan-stacking VLAN Stacking port mode

[ Accept Frame Type ]

switchport acceptable-frame-types all

command is used to allow the interface port(s) to accept all types of frame.

switchport acceptable-frame-types tagged

command is used to allow the interface port(s) to accept tagged frame

only. Other frame type will be rejected.

[ VLAN Port Assignment ]

switchport allowed vlan add x

command will add the interface port(s) to VLAN x. “

” is the VLAN ID and its

valid value is 2~-4094.

switchport allowed vlan remove x

command will remove the interface port(s) from VLAN x. “

” is the VLAN ID

and its valid value is 2~-4094.

[ VLAN Port Mode Setting for Private VLAN ]

switchport mode private-vlan host

command will set the port type of the interface port(s) in Private VLAN as

“host”. “host” port(s) could be for Community VLAN or Isolated VLAN.

switchport mode private-vlan promiscuous

command will set the port type of the interface port(s) in Private

VLAN as “promiscuous”. “promiscuous” port(s) could be for Primary VLAN or Isolated VLAN.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды