CTC Union GSW-3208M Скачать руководство пользователя страница 46

Страница: 46 / 148

Chapter 6. Manage / Configure the Switch

username admin www xxx yyy zzz

command is used to set the username and password for administrator. “

www

” is

the old username. “

xxx

” is the old password. “

yyy

” is the new username. “

zzz

” is the new password.

username guest yyy zzz

command is used to set the username and password for guest. “

yyy

” is the new username.

“

zzz

” is the new password.

Administrator is the user who has the right to do configuration modification. Guest is the user who has the right to

view configuration only.

vlan

command

This command is used to enter VLAN configuring mode. And the prompt will become ...

(config)# vlan database

(config-vlan)#

The operations for VLAN are configured in VLAN configuring mode. Please refer to

6.2.5 VLAN Configuring

Commands

section for the details.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды