CTC Union GSW-3208M Скачать руководство пользователя страница 8

Страница: 8 / 148

Chapter 2 Installation

Chapter 2. Installation

This Switch can be placed on a flat surface (your desk, shelf or table).

Place the Switch at a location with these connection considerations in mind:

The switch configuration does not break the rules as specified in Section 3.

The switch is accessible and cables can be connected easily to it.

The cables connected to the switch are away from sources of electrical interference such as radio, computer monitor, and

light fixtures.

There is sufficient space surrounding the switch to allow for proper ventilation (the switch may not function according to

specifications outside of the temperature range of 0 to 50 degrees C).

For GSW-3416M / GSW-34224M model, you can also install the switch on a 19" rack with the rack-mount kits as pictured.

<< Rack-Mount Installation >>

Before rack mounting the switch, please pay attention to the following factors:

Temperature

- Because the temperature in a rack assembly could be higher than the ambient room temperature, check

that the rack-environment temperature is within the specified operating temperature range. (Please refer to Product

Specifications in the manual.) Air flow is necessary in a rack for temperature stable.

Mechanical Loading

- Do not place any equipment on top of this rack-mounted switch.

Circuit Overloading

- Be sure that the supply circuit to the rack assembly is not overload after installing this switch.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды