CTC Union GSW-3208M Скачать руководство пользователя страница 30

Страница: 30 / 148

Chapter 6. Manage / Configure the Switch

For “Auto Negotiation” mode, the switch will disable port auto-negotiation function when the auto function of port

(in Port Configuration setting) is disabled.

For “Auto Detect” mode, the switch will always keep port auto-negotiation function ON but just modify its

attribution if auto function of port (in Port Configuration setting) is disabled.

For applications, you should select “Auto Detect

”

mode if the connected device is auto-negotiation enabled. (For

example, customer’s PC is auto-negotiation enable and you want to set his network connection to work at 10Mbps.)

And you can select “Auto Negotiation

”

mode if the connected device is auto-negotiation disabled (it is called forced

mode, sometimes). Some old TX-FX Converters needs to work in this mode because FX supports 100/Full forced

mode only. For most applications, “Auto Detect” mode is OK.

With “automode ?”, the sub-commands will be shown.

(config)# automode ?

detect Auto Detect mode

negotiation Auto Negotiation mode

automode detect

command will set it to auto-detect mode.

automode negotiation

command will set it to auto-negotiation mode.

default

command

This command is used to restore factory default settings. Before start it, a confirm message wil be prompted.

dhcp-relay

command

This command is used to configure DHCP Relay Option 82 function. DHCP Relay Option 82 function will add the

following information to DHCP request packet ...

Port number that the DHCP request packet comes from

Mac address of the switch

A additional string as information. (*Adding the information string must be enabled first.)

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды