CTC Union GSW-3208M Скачать руководство пользователя страница 39

Страница: 39 / 148

Chapter 6. Manage / Configure the Switch

management x protocol http|snmp|telnet

command is used to enable the remote management protocol for some

user groups (“

” is the index of the user group). More than one protocols can be enabled at the same time - e.g.

“management 2 protocol http snmp telnet”. And

no management x protocol

command is used to disable all remote

management protocols for the user group.

mirror

command

This command is used to enable mirror function of the switch. And

no mirror

command can be used to disable

mirror function of the switch.

mvr

command

This command is used to configure MVR (Multicast VLAN Registration) function. VLAN function will isolate

traffic between VLAN groups. But it will also isolate IP multicast traffic for subscribers in different VLANs. The

MVR function allows one multicast VLAN to be shared by subscribers in different VLANs. That can reduce the

multicast traffic for VLANs.

** Before configuring MVR function, complete the VLAN setting first

** Using MVR function, you have to enable IGMP snooping function first.

This switch supports three MVR VLANs. They are referred with their VLAN ID. For any MVR setting, you have to

assign the VLAN ID in the command.

Entering “mvr x ?”, the sub-commands will be shown. “x” is a VLAN ID with number in 2~4094. For example,

“mvr 10”.

(config)# mvr 10 ?

8021p-priority Configure 802.1p priority tagging

active Active a MVR VLAN

group Create a multicast group for MVR VLAN

mode Set MVR VLAN operation mode

name Set MVR VLAN name

<cr> Create a MVR VLAN

mvr x

command is used to create a MVR VLAN with VLAN ID “

”. “

no mvr x

” command is used to delete a MVR

VLAN.

mvr x 8021p-priority y

command is used to set the 802.1P priority (0~7) for MVR operation. The IGMP control

packets for this VLAN will be assigned this priority when tag is added. “

” is the MVR VLAN ID. “

” is the 802.1P

priority value.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды