CTC Union GSW-3208M Скачать руководство пользователя страница 62

Страница: 62 / 148

Chapter 6. Manage / Configure the Switch

Entering “interface vlan 100”, and its prompt will become ...

(config)# interface vlan 100

(config-if)#

Enter “?” at the prompt, the sub-command list will be shown.

-------------------------------------------------------------------------------

(config-if)# ?

exit Exit from current mode

help Show available commands

history Show a list of previously run commands

logout Disconnect

quit Quit commands

interface Enters privileged interface configuration

Internet protocol

no Negates a command or sets its defaults

-------------------------------------------------------------------------------

exit

command

This command is used to leave current operation mode. Go back to last mode.

help

command

This command is used to show all the available commands in this mode.

history

command

This command is used to show the history of entering commands.

logout

command

This command is used to logout from console interface.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды