CTC Union GSW-3208M Скачать руководство пользователя страница 18

Страница: 18 / 148

Chapter 6. Manage / Configure the Switch

6.2 Settings with Console Connection

6.2.1 Basic of the Console Interface

<< Enter Console Interface >>

Please follow the steps to complete the console hardware connection first.

Connect from console port of the switch to COM port of PC with the console cable.

Start the terminal program of Windows. Create a new connection and select COM port of PC used for the console.

Set the configuration of the terminal as

[9600,8,N,1]

. (You can find the terminal program in [Start] -> [Programs] ->

[Accessory Programs] -> [Communication] -> [Terminal]. If you cannot find it, please install it from your Windows

Installation Disk. Please refer to your Windows user manual for the installation.)

Power on the switch.

If everything is correct, the booting screen will appear in the terminal program when the switch is powered on. It will

stop at the following screen after some initializing messages.

------------------------------------------------------------------------------------

Booting Program Version 1.04.04-SI/PI, built at 12:04:53, Sep 17 2008

RAM: 0x00000000-0x00800000, 0x0000cc78-0x007f3000 available

FLASH: 0x05800000 - 0x05a00000, 32 blocks of 0x00010000 bytes each.

enter ^C to abort booting within 3 seconds ......

Start to run system initialization task...

[System Configuration]

Company Name :

Model Name : Switch

MAC Address : 00:12:34:64:99:6F

Firmware version : 1.04.1

Username:

------------------------------------------------------------------------------------

<< User Modes >>

There are two user modes for the switch - one is administrator mode (privileged mode), another is guest mode (normal

mode).

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды