CTC Union GSW-3208M Скачать руководство пользователя страница 66

Страница: 66 / 148

Chapter 6. Manage / Configure the Switch

history

command

This command is used to show the history of entering commands.

logout

command

This command is used to logout from console interface.

quit

command

This command is used to quit from console interface. It has the same function as logout.

end

command

This command is used to exit from VLAN Configuring mode.

(config-vlan)# end

(config)#

1q-vlan

command

This command is used to configure 802.1Q VLAN characteristics.

(config-vlan)# 1q-vlan ?

gvrp Enables GVRP globally for the switch

ingress-filtering Configures frame filtering base on VLAN membership

<cr>

1q-vlan

command can enable 802.1Q VLAN function. And

no 1q-vlan

command can disable it.

1q-vlan gvrp

command is used to enable GVRP function of 802.1Q VLAN. This command works only if 802.1Q

VLAN is enabled. And GVRP will be disable automatically when 802.1Q VLAN is set to disable.

no 1q-vlan gvrp

command can disable it.

1q-vlan ingress-filtering

command is used to enable doing VLAN membership filtering at ingress port instead of

egress port.

no 1q-vlan ingress-filtering

command can disable it.

Содержание GSW-3208M





















































































































































Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды

CTC Union GSW-3208M, Руководство пользователя

Результаты поиска

Содержание GSW-3208M

Отзывы:

Похожие инструкции для GSW-3208M

Бренды по названию

Популярные бренды