manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 7 OSPFv3 Configuration

Parameter

Description

<

type

>

Specifies the metric-type of the redistributed LSA. The value

is 1-2. The default value is 2.

route-map

<

map-name

>

Specifies the route map used for protocol route redistribution.

The command parameter in step 13 is described as follows:

Parameter

Description

<

X:X::X:X/128

>

Prefix and prefix length of the IPv6 routes summarized.

The command parameters in step 14 are described as follows:

Parameter

Description

<

delay

>

Specifies the delay of route re-computation that follows after

route updates are received in the unit of seconds. The value

range is 0-65535. The default value is 5 seconds.

<

holdtime

>

Specifies the hold time in the unit of seconds. The value

range is 0-65535. The default value is 10 seconds.

7.3 OSPFv3 Maintenance and Diagnosis

Compared with RIPng, OSPFv3 is more complicated. There are many fault reasons behind

a fault symptom. Therefore, the maintenance and diagnosis of OSPFv3 is more difficult.

To maintain and diagnose OSPFv3, use the following commands.

Command

Function

ZXR10(config)#

show ipv6 ospf

<

process id

>

Shows an OSPFv3 instance.

ZXR10(config)#

show ipv6 ospf database

Shows the database information

about an OSPFv3 instance.

ZXR10(config)#

show ipv6 ospf interface

[<

interface-name

>]

Shows the interface information

about an OSPFv3 instance.

ZXR10(config)#

show ipv6 ospf neighbor

Shows the neighbor information

about an OSPFv3 instance.

ZXR10(config)#

show ipv6 ospf virtual-links

Shows the virtual link information

about an OSPFv3 instance.

The following example shows the outputs of the command

show ipv6 ospf

:

ZXR10#show ipv6 ospf

Routing Process "ospfv3 1" with ID 1.1.1.8

SPF schedule delay 5 secs. Hold time between two SPFs 10 secs

Minimum LSA interval 5 secs. Minimum LSA arrival 1 secs

7-11

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link Verizon DSL-2750B Connection Instructions preview
Verizon DSL-2750B
Brand: D-Link Pages: 2
D-Link DVA-2800 Quick Start Manual preview
DVA-2800
Brand: D-Link Pages: 4
Watchguard Firebox T15 Quick Start Manual preview
Firebox T15
Brand: Watchguard Pages: 39
TP-Link TD-8817 User Manual preview
TD-8817
Brand: TP-Link Pages: 73
Axis AXIS P1354 Installation Manual preview
AXIS P1354
Brand: Axis Pages: 104
EMCIS LISN User'S Operating Manual preview
LISN
Brand: EMCIS Pages: 14
NETGEAR WAG302 Installation Manual preview
WAG302
Brand: NETGEAR Pages: 2
Perle P841 Specifications preview
P841
Brand: Perle Pages: 2
UfiSpace S9600-64X Hardware Installation Manual preview
S9600-64X
Brand: UfiSpace Pages: 35
SAGEMCOM SE681 WiMAX User Manual preview
SE681 WiMAX
Brand: SAGEMCOM Pages: 75
Alcatel Speed Touch 591s Technical User'S Manual preview
Speed Touch 591s
Brand: Alcatel Pages: 184
Zhone ETHX-2214-DS3 Installation Instructions Manual preview
ETHX-2214-DS3
Brand: Zhone Pages: 28
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
Hanwha Techwin Wisenet PRN-6400DB4 User Manual preview
Wisenet PRN-6400DB4
Brand: Hanwha Techwin Pages: 125
Lanner ECA-4027 User Manual preview
ECA-4027
Brand: Lanner Pages: 99
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
Alcatel 7750 SR-12 Installation Manual preview
7750 SR-12
Brand: Alcatel Pages: 158
Altronix NetWay8GL Installation Manual preview
NetWay8GL
Brand: Altronix Pages: 8

Brands by name

Popular brands

Load more brands