manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 20 DHCPv6 Configuration

6.

Configure a DHCPv6 server.

Configure server mode in DHCPv6 interface

configuration mode. Bind the policy.

Configuration Commands

Configuration on ZXR10:

ZXR10(config)#switchvlan-configuration

ZXR10(config-swvlan)#interface gei-0/1/1/1

ZXR10(config-swvlan-if-gei-0/1/1/1)#switchport access vlan 10

ZXR10(config-swvlan-if-gei-0/1/1/1)#exit

ZXR10(config-swvlan)#exit

ZXR10(config)#interface vlan10

ZXR10(config-if)#ipv6 enable

ZXR10(config-if)#ipv6 add 86::1:1/96

ZXR10(config-if)#exit

/*Configure an IPv6 address pool*/

ZXR10(config)#ipv6 addr-pool zte

ZXR10(config-ipv6-addr-pool)#addr-range 86::1:2 86::1:10

ZXR10(config-ipv6-addr-pool)#exit

/*Enable DHCPv6*/

ZXR10(config)#dhcp ipv6

ZXR10(config-dhcpv6)#enable

/*Bind the IPv6 address pool to the DHCPv6 pool*/

ZXR10(config-dhcpv6)#pool zte

ZXR10(config-dhcpv6-pool)#address-lifetime 1000 1000

ZXR10(config-dhcpv6-pool)#exit

/*Bind the DHCPv6 pool to the DHCPv6 policy*/

ZXR10(config-dhcpv6)#policy zte 1

ZXR10(config-dhcpv6-policy)#dhcpv6-pool

zte

ZXR10(config-dhcpv6-policy)#exit

/*Configure server mode in interface configuration mode and bind the policy*/

ZXR10(config-dhcpv6)#inter vlan10

ZXR10(config-dhcpv6-if)#mode server

ZXR10(config-dhcpv6-if)#server policy zte

ZXR10(config-dhcpv6-if)#exit

Configuration Verification

Check the configuration of the IPv6 address pool on ZXR10, as shown below.

ZXR10#show ipv6 addr-pool zte

20-11

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link Verizon DSL-2750B Setup Manual preview
Verizon DSL-2750B
Brand: D-Link Pages: 6
D-Link DIR-857 Quick Installation Manual preview
DIR-857
Brand: D-Link Pages: 10
D-Link DSL-2740U Quick Installation Manual preview
DSL-2740U
Brand: D-Link Pages: 38
Billion BiPAC 4500NZ(L) User Manual preview
BiPAC 4500NZ(L)
Brand: Billion Pages: 146
4IPNET WHG301 User Manual preview
WHG301
Brand: 4IPNET Pages: 97
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
LaCie 5big Network 2 Datasheet preview
5big Network 2
Brand: LaCie Pages: 4
LaCie d2 Network 2 Datasheet preview
d2 Network 2
Brand: LaCie Pages: 4
LaCie 2big Network 2 Datasheet preview
2big Network 2
Brand: LaCie Pages: 4
Aztech DSL5068EN(1T1R) User Manual preview
DSL5068EN(1T1R)
Brand: Aztech Pages: 40
ZoneVu ZSI-450-IP Installation Manual & User Manual preview
ZSI-450-IP
Brand: ZoneVu Pages: 15
Ovislink Air Live GW-300R User Manual preview
Air Live GW-300R
Brand: Ovislink Pages: 20
SMC Networks EZ Switch SMC-EZ1024FDT Specification Sheet preview
EZ Switch SMC-EZ1024FDT
Brand: SMC Networks Pages: 4
Lanner ECA-4027 User Manual preview
ECA-4027
Brand: Lanner Pages: 99
Goonas LC180 User Manual preview
LC180
Brand: Goonas Pages: 13
Acard ARS-2212 User Manual preview
ARS-2212
Brand: Acard Pages: 43
Paradyne MIM-4T1 Installation Instructions Manual preview
MIM-4T1
Brand: Paradyne Pages: 10
ASTRO U 960 Operating Manual preview
U 960
Brand: ASTRO Pages: 12

Brands by name

Popular brands

Load more brands