manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

1.

Configure the IP addresses of gei-0/1/1/1 and gei-0/1/1/2 interfaces.

2.

Enter the multicast mode.

3.

Enable static multicast routing.

4.

Configure the maximum number of static multicast routes (*, G) and (S, G).

5.

Configure a list of static multicast egress interfaces.

6.

Configure a static multicast route.

l

Configuration Commands

Run the following commands on S1:

S1(config)#ipv6 multicast-routing

S1(config-mcast-ipv6)#ipv6 multicast-static-start

S1(config-mcast-ipv6)#ipv6 multicast-static-limit xg 1024 sg 1024

S1(config-mcast-ipv6)#ipv6 multicast-static-interface index 2 interface gei-0/1/1/2

S1(config-mcast-ipv6)#ipv6 multicast-static-route 1::1 ff88::1 iif gei-0/1/1/1 oif 2

S1(config-mcast-ipv6)#end

l

Configuration Verification

Run the

show ipv6 multicast-static-interface

command on S1 to display static multicast

information about the interfaces:

S1(config)#show ipv6 multicast-static-interface

STATIC-MULTICAST OUT PORT INDEX 2:

Outgoing Interface: gei-0/1/1/2

S1(config)#show ipv6 multicast-static-route

The Capability of Static Multicast6 Route

(*, g) 1024, (s, g) 1024

(1::1, ff88::1)

Incoming interface: gei-0/1/1/1

A

Outgoing interface list:

gei-0/1/1/2

N

15-4

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

LaCie 5BIG NAS PRO Quick Install Manual preview
5BIG NAS PRO
Brand: LaCie Pages: 22
Allied Telesis AT-8000C Declaration Of Conformity preview
AT-8000C
Brand: Allied Telesis Pages: 1
Paradyne 7510 DSU Start-Up Instructions preview
7510 DSU
Brand: Paradyne Pages: 10
Xenya XS26GS User Manual preview
XS26GS
Brand: Xenya Pages: 189
B+B SmartWorx spectre lte User Manual preview
spectre lte
Brand: B+B SmartWorx Pages: 52
CyberTAN WR214C User Manual preview
WR214C
Brand: CyberTAN Pages: 67
Compro Technology RS-2104 Quick Installation Manual preview
RS-2104
Brand: Compro Technology Pages: 2
Korenix JetNet 3705 User Manual preview
JetNet 3705
Brand: Korenix Pages: 25
LaView LV-KN series Quick Start Manual preview
LV-KN series
Brand: LaView Pages: 2
NetComm Dynalink MyZone 3G24W Remote Administration Setup preview
Dynalink MyZone 3G24W
Brand: NetComm Pages: 5
Toto Link ND300V2 Manual preview
ND300V2
Brand: Toto Link Pages: 57
Infoblox ND-2200 Installation Manual preview
ND-2200
Brand: Infoblox Pages: 44
Topcom Wireless Kit 108MBPS User Manual preview
Wireless Kit 108MBPS
Brand: Topcom Pages: 100
National Instruments NI ELVIS III Getting Started preview
NI ELVIS III
Brand: National Instruments Pages: 37
Tripp Lite N306-05M Specification Sheet preview
N306-05M
Brand: Tripp Lite Pages: 2
Digi TransPort WR11 XT Quick Start Manual preview
TransPort WR11 XT
Brand: Digi Pages: 4
Muratec OFFICEBRIDGE ONLINE User Manual preview
OFFICEBRIDGE ONLINE
Brand: Muratec Pages: 220
Greenlee GREENLEE SURE SIGNAL 46060 Instruction Manual preview
GREENLEE SURE SIGNAL 46060
Brand: Greenlee Pages: 2

Brands by name

Popular brands

Load more brands