Zte ZXR10 5900E Series Configuration Manual Download Page 83

Page: 83 / 226

Chapter 7 OSPFv3 Configuration

Step

Command

Function

ZXR10(config-ospfv3-process-id-if-interface-

name)#

priority

value

Sets the interface priority in

the unit of seconds. The value

range is 0-255. The default

value is 1.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

neighbor

X:X::X:X

>[{[

cost

cost-value

>]|[

poll-inter

val

interval

>]|[

priority

value

>]}]

Configures the neighboring

routers in a non-broadcast or

point-to-multipoint network.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

network

{

broadcast

non-broadcast

point-to-multipoint

[

non-broadcast

point-to-point

}

Sets the network type for an

interface.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

bfd

disable

enable

Configures BFD attribute.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

ipv6-mtu-ignore

Configures to ignore MTU

check during DD packet

exchange

ZXR10(config-ospfv3-process-id-if-interface-

name)#

linklsa-suppress

enable

Suppresses an interface to

generate Type-8 link LSA.

Configuring OSPFv3 Protocol Attributes

To configure OSPFv3 protocol attributes, perform the following steps.

Step

Command

Function

ZXR10(config)#

ipv6 router ospf

process-id

Enables an OSPFv3 instance

and enters the OSPFv3

configuration mode.

ZXR10(config-process-id)#

area

area-id

bfd

disable

enable

Configures BFD attribute of all

interface in an area.

ZXR10(config-ospfv3)#

area

area-id

default-cost

cost-value

Configures the default metric

value for an area, the value

range is 0-16777215.

ZXR10(config-ospfv3)#

area

area-id

range

X:X::X:X/

0-128

advertise

not-advertise

]

Configures the range of

summary addresses in an

area.

ZXR10(config-ospfv3)#

area

area-id

stub

[

no-summary

]

Defines an area as the stub

area.

no-summary

implies

the ABR is forbidden to send

summary routes to this stub

area.

7-7

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands

Zte ZXR10 5900E Series, Configuration Manual

Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands