Zte ZXR10 5900E Series Configuration Manual Download Page 179

Page: 179 / 226

Chapter 14

IPv6 PIM-SSM Configuration

Table of Contents

PIM-SSM Overview ..................................................................................................14-1

Configuring IPv6 PIM-SSM.......................................................................................14-1

IPv6 PIM-SSM Maintenance and Diagnosis .............................................................14-2

IPv6 PIM-SSM Configuration Example .....................................................................14-3

14.1 PIM-SSM Overview

Protocol Independent Multicast-Source Specific Multicast (

PIM-SSM

) has all advantages

of PIM-SM. PIM-SSM does not construct a shared tree. Instead, it only constructs the

SPT. When receiving the member relation report messages about a specific source and a

group, PIM-SSM will construct the SPT directly.

PIM-SSM is a subset of PIM-SM. PIM-SSM is suitable for the well known sources. It is

both intra-domain and inter-domain valid. PIM-SM uses MSDP for inter-domain multicast

routing. PIM-SSM does not need to use MSDP. The multicast group address allocated

for PIM-SSM is FF3X::/32. The switches will not construct a shared tree for this group

address.

After a host sends a Join message from a specific source to a group, the last hop switch

will send a (S, G) Join message to the direction of the source to construct a SPT. The last

hop switch will not send a (*, G) Join message to the direction of RP. Once the SPT is

constructed, the first hop switch will forward packets along this tree.

14.2 Configuring IPv6 PIM-SSM

To configure IPv6 PIM-SSM on ZXR10 5900E, perform the following step.

Command

Function

ZXR10(config-mcast-ipv6-pim)#

ssm range default

[

group-list

access-list-name

Configures address range of IPv6

SSM groups or uses the default

group address range.

The command parameter is described as follows:

Parameter

Description

access-list-name

ACL name, with 1-31 characters

When the

group-list

is not configured, the default group range is FF3X::/32.

14-1

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands

Zte ZXR10 5900E Series, Configuration Manual

Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands