manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

Step

Command

Function

ZXR10(config-if-interface-name)#

ipv6 nd suppress-ra

Prohibits the router from

sending router advertisement

packets.

9

ZXR10(config-if-interface-name)#

no ipv6 nd

suppress-ra

Enables the router to send

router advertisement packets.

ZXR10(config-if-interface-name)#

ipv6 nd

ra-curhoplimit

Configures the counter limit of

router advertisement hops.

10

ZXR10(config-if-interface-name)#

no ipv6 nd

ra-curhoplimit

Restores the hop limit of

routing advertisement to the

default value.

ZXR10(config-if-interface-name)#

ipv6 nd staled-time

Configures the staled-time of

ND entities in the neighbor

cache table. The time is in unit

of minute, and in the range of

1-14400.

11

ZXR10(config-if-interface-name)#

no ipv6 nd

staled-time

Restores the default value of

the stale status period of the

nd entry in the neighbor's catch

table.

ZXR10(config-if-interface-name)#

ipv6 nd stale-switch

Configures reachability

detection before staled-time

expires.

12

ZXR10(config-if-interface-name)#

no ipv6 nd

stale-switch

Disables reachability detection

before staled-time expires.

By default, the reachability

detection function is not

enabled.

ZXR10(config-if-interface-name)#

ipv6 nd ra-linkmtu

<

mtu

>

Sets the mtu field in route

advertisement. Range:

0-1500, default: 1500.

13

ZXR10(config-if-interface-name)#

no ipv6 nd

ra-linkmtu

Restores the default value

of the linkmtu in route

advertisement.

ZXR10(config-if-interface-name)#

nd6 add

<

ipv6-address

><

hardware-address

>

Adds a static entry to the

neighbor cache table.

14

ZXR10(config-if-interface-name)#

nd6 delete

<

ipv6-address

>

Deletes a static entry from the

neighbor cache table.

15

ZXR10#

clear nd-cache

Clears all the entries in the

IPv6 neighbor cache table.

2-4

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

Barracuda Networks Network Quick Start Manual preview
Network
Brand: Barracuda Networks Pages: 2
Canon Vb-C60 - Ptz Network Camera Setup Manual preview
Vb-C60 - Ptz Network Camera
Brand: Canon Pages: 30
Aastra CNX Product Brief preview
CNX
Brand: Aastra Pages: 2
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
X-Micro WLAN 11g User Manual preview
WLAN 11g
Brand: X-Micro Pages: 74
Watchguard XTM 5 Series Hardware Manual preview
XTM 5 Series
Brand: Watchguard Pages: 24
XAVI Technologies Corp. 7721r User Manual preview
7721r
Brand: XAVI Technologies Corp. Pages: 71
WaiLan DeltaFire 500 User Manual preview
DeltaFire 500
Brand: WaiLan Pages: 27
3Com 3C589D User Manual preview
3C589D
Brand: 3Com Pages: 50
eWON 2101CD Installation Manual preview
2101CD
Brand: eWON Pages: 34
B&B Electronics Elinx EIR510 Series Quick Start Manual preview
Elinx EIR510 Series
Brand: B&B Electronics Pages: 2
Casablanca W-500 Technical Bulletin preview
W-500
Brand: Casablanca Pages: 13
Zhone ETHX-2214-DS3 Installation Instructions Manual preview
ETHX-2214-DS3
Brand: Zhone Pages: 28
Stahl HFisolator 9730/26-11 Operating Instructions preview
HFisolator 9730/26-11
Brand: Stahl Pages: 2
ZyXEL Communications GS-2724 User Manual preview
GS-2724
Brand: ZyXEL Communications Pages: 348
IBM Redbooks Emulex VFA5 Product Manual preview
Redbooks Emulex VFA5
Brand: IBM Pages: 15
Panduit CDPP8RG-S Installation Instructions preview
CDPP8RG-S
Brand: Panduit Pages: 5
8e6 Technologies Threat Analysis Reporter TAR HL/SL/MSA Evaluation Manual preview
Threat Analysis Reporter TAR HL/SL/MSA
Brand: 8e6 Technologies Pages: 22

Brands by name

Popular brands

Load more brands