Zte ZXR10 5900E Series Configuration Manual Download Page 134

Page: 134 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

Command Output

Description

All sent 33 messages 5 updates, 1

opens, 27 keepalives

Totally 33 messages are sent, among which there are 5

update messages, 1 open message and 27 keepalive

message.

After last established sent 31

messages

5 updates, 0 opens, 26 keepalives

Totally 31 messages are sent since the neighbor relationship

was established last time, among which there are 5 update

message, 0 open message and 26 keepalive messages.

For address family: IPv4 Unicast no

activate

Indicates that unicast IPv4 routes are described below. IPv4

unicast function is not activated.

All received nlri 0, unnlri 0, 0 accepted

prefixes

There is no NLRI message, no withdraw message and no

unicast prefix received.

All sent nlri 0, unnlri 0, 0 advertised

prefixes

here is no NLRI message, no withdraw message and no

unicast prefix sent.

Maximum limit 4294967295

Threshold for warning message 75%

The maximum limit is 4294967295s. The threshold to send

warning messages is 75%.

For address family: IPv6 Unicast

Indicates that unicast IPv6 routes are described below.

Med attribute sent to this neighbor

MED attribute is sent to local device.

All received nlri 5, unnlri 0, 5 accepted

prefixes

There are 5 NLRI messages, no withdraw message and 5

unicast prefixes received.

All sent nlri 7, unnlri 6, 1 advertised

prefixes

There are 7 NLRI messages, 6 withdraw message and 1

unicast prefix received.

Maximum limit 4294967295

Threshold for warning message 75%

The maximum limit is 4294967295s. The threshold to send

warning messages is 75%.

For address family: VPNv6 Unicast

no activate

Indicates that unicast IPv6 routes are described below. IPv6

unicast function is not activated.

For address family: IPv6 multicast no

activate

Indicates that multicast IPv6 routes are described below.

IPv6 multicast function is not activated.

Connections established 1

BGP neighbor relationship is established once with the peer.

Local host: 2002:9::1, Local port:

4331

Local IP host, including local IP address and TCP port

number

Foreign host: 2002:9::2, Foreign port:

179

Peer IP host, including peer IP address and TCP port number

The following is a sample output from the

show bgp ipv6 unicast

command:

ZXR10#show bgp ipv6 unicast

Status codes: *valid, >best, i-internal

Origin codes: i-IGP, e-EGP, ?-incomplete

Network

Next Hop

Metric

LocPrf

RtPrf Path

*> 1:1::/32

2002:9::2

100

300 i

9-6

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands

Zte ZXR10 5900E Series, Configuration Manual

Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands