manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

Step

Command

Function

2

ZXR10(config-ripng)#

interface

<

interface-name

>

Enters the RIPng interface

configuration mode.

ZXR10(config-ripng-if)#

ipv6 rip split-horizon

Enables split horizon on

the interface. By default,

split horizon is enabled. To

disable split horizon, use the

no

form of the command.

ZXR10(config-ripng-if)#

ipv6 rip poison-reverse

Enables poison reverse on

the interface. By default, the

poison reverse function is

enabled.

ZXR10(config-ripng-if)#

ipv6 rip interface active

Configures the active

interface so that the interface

only sends packets but

does not receive packets.

To cancel the configuration

and restore normal packet

sending and receiving, use

the

no

form of the command.

ZXR10(config-ripng-if)#

ipv6 rip interface passive

Configures the passive

interface so that the interface

only receives packets but

does not send packets. To

cancel the configuration

and restore normal packet

sending and receiving, use

the

no

form of the command.

ZXR10(config-ripng-if)#

ipv6 rip neighbor

<

X:X::X:X

>

Configures the neighbor

address of the RIPng so that

unicast packets will be sent

to this neighbor only.

3

ZXR10(config-ripng-if)#

ipv6 rip originate-default-

route

[

only

]

Originates the default route

of the RIPng on the interface.

To cancel the configuration,

use the

no

form of the

command.

The command parameters in step 3 are described as follows:

Parameter

Description

<

X:X::X:X

>

Specifies the link-local address of the neighbor.

6-6

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

Paradyne Hotwire 5446 Notice preview
Hotwire 5446
Brand: Paradyne Pages: 2
Paradyne Hotwire 6381 Installation Instructions Manual preview
Hotwire 6381
Brand: Paradyne Pages: 20
Paradyne Hotwire 6381 Upgrade Instructions preview
Hotwire 6381
Brand: Paradyne Pages: 2
Zhone Hotwire 6381 Quick Installation Instructions preview
Hotwire 6381
Brand: Zhone Pages: 2
Paradyne COMSPHERE 6800 Series Multiplexer Management And Configuration Manual preview
COMSPHERE 6800 Series
Brand: Paradyne Pages: 155
Paradyne COMSPHERE 6800 Series Communications Products Support Configuration Manual preview
COMSPHERE 6800 Series
Brand: Paradyne Pages: 44
Watchguard Firebox SOHO 6 Wireless Instructions Manual preview
Firebox SOHO 6 Wireless
Brand: Watchguard Pages: 8
LORD AP5103 Series Technical Manual preview
AP5103 Series
Brand: LORD Pages: 9
PairGain PG-FLEX RT FRL-752 Manual preview
PG-FLEX RT FRL-752
Brand: PairGain Pages: 6
IBM BladeCenter Management Module Installation And User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 184
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
Matrix Switch Corporation MSC-1HD1608L Product Manual preview
MSC-1HD1608L
Brand: Matrix Switch Corporation Pages: 60
LevelOne NetCon FBR-1409TX User Manual preview
NetCon FBR-1409TX
Brand: LevelOne Pages: 88
H3C SecPath F1070 Manual preview
SecPath F1070
Brand: H3C Pages: 68
Deliberant APC Mach 5 V3 Quick Installation Manual preview
APC Mach 5 V3
Brand: Deliberant Pages: 16
Buffalo AirStation G54 WLA2-G54 Quick Setup Manual preview
AirStation G54 WLA2-G54
Brand: Buffalo Pages: 8
Xinje VH5 Series User Manual preview
VH5 Series
Brand: Xinje Pages: 76
Juniper WX 100 Quick Start Manual preview
WX 100
Brand: Juniper Pages: 6

Brands by name

Popular brands

Load more brands