manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

For a description of the sample output from the

show isis database

command, refer to the

following table:

Command Output

Description

Process-id

IS-IS instance number, range: 0–65535.

LSP ID

Indicates the LSP ID in the form of xxxx.xxxx.xxxx.xx-xx.

LSP Seq Num

Indicates the LSP sequence number in the form of

0xdddddddd.

LSP Checksum

Indicates the LSP checksum in the form of 0xdddd.

LSP Holdtime

Indicates the LSP lifetime in the form of a common number.

ATT/P/OL

Indicates the ATT (Whether to connect with external areas)

flag bit/partitioning bit/overload bit.

IS neighbor

Indicates the IS neighbor.

IP-Internal/IP-External

Indicates the reachable IP address.

Area Address

Indicates the area address.

NLPID

Indicates the supported protocol.

Hostname

Indicates the host name.

Ip Address

Indicates the port IP address.

IPv6 Address

Indicates the port IPv6 address.

Inter-Domain Info

Indicates the inter-domain information (Tag).

The following is a sample output from the

show isis circuit

command:

ZXR10(config)#show isis circuits

Process ID: 0

Interface

State

Lev

CirId

Level1-DR

Level2-DR

Pri(L1/L2)

vlan1

Up

L1L2

2

Dis is me

Dis is me

64/64

ZXR10(config)#

For a description of the sample output from the

show isis circuit

command, refer to the

following table:

Command Output

Description

Process-id

IS-IS instance number, range: 0–65535.

Interface

Indicates the interface name.

State

Indicates whether the IS-IS protocol is enabled on the

interface. "UP" indicates that the IS-IS protocol is enabled.

"DOWN" indicates that the protocol is disabled.

Lev

Indicates the port level, which can be "L1", "L2", or "L1L2".

CirId

Indicates the port ID.

8-16

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Linke DHP-346AV Quick Installation Manual preview
DHP-346AV
Brand: D-Linke Pages: 32
Netopia 3346-ENT Getting Started Manual preview
3346-ENT
Brand: Netopia Pages: 38
Enginko MCF-LW06424 Operating Manual preview
MCF-LW06424
Brand: Enginko Pages: 19
CELOT CTR-180 User Manual preview
CTR-180
Brand: CELOT Pages: 34
Waver WAC52N Quick Start Manual preview
WAC52N
Brand: Waver Pages: 36
Hi-flying HF-LPB User Manual preview
HF-LPB
Brand: Hi-flying Pages: 59
Maestro Wireless Solution E220 Series Quick Start Manual preview
E220 Series
Brand: Maestro Wireless Solution Pages: 22
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
Oracle Database Appliance X6-2-HA Deployment And User'S Manual preview
Database Appliance X6-2-HA
Brand: Oracle Pages: 473
NetComm 3G15Wn Manual preview
3G15Wn
Brand: NetComm Pages: 2
Cambium Networks PTP 850E Installation Manual preview
PTP 850E
Brand: Cambium Networks Pages: 99
Crestron RACK2 Operation Manual preview
RACK2
Brand: Crestron Pages: 52
Lakeside Alto Room Scaffold Instruction Manual preview
Alto Room Scaffold
Brand: Lakeside Pages: 12
EDSLab WiDRIVE User Manual preview
WiDRIVE
Brand: EDSLab Pages: 24
NetComm NB1 User Manual preview
NB1
Brand: NetComm Pages: 91
NetComm NB6 User Manual preview
NB6
Brand: NetComm Pages: 152
NetComm NF2 Product Data Sheet preview
NF2
Brand: NetComm Pages: 2
NetComm V210P Connection Manual preview
V210P
Brand: NetComm Pages: 13

Brands by name

Popular brands

Load more brands