manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 1 IPv6 Address Configuration

An IPv6 host has many IPv6 addresses even if it has only one single interface. An

IPv6 host can have the following unicast addresses simultaneously.

à

The link-local address of each interface

à

The unicast address of each interface, which can be a site-local address or one

or more aggregable global addresses

à

Loopback address (::1) of a loopback interface

In addition, each host must always keep receiving the data from the following multicast

addresses.

à

Multicast addresses (FF01::1) of all the nodes within the node-local range

à

Multicast addresses (FF02::1) of all the nodes within the link-local range

à

Multicast address of the solicited-node (if the solicited-node group is added to an

interface of the host)

à

Multicast address of a multicast group (if any multicast group is added to an

interface of the host)

l

IPv6 Router Address

The following unicast addresses can be allocated to an IPv6 router:

à

Link-local address of each interface

à

Unicast address of each interface, which can be a site-local address or one or

more aggregable global addresses

à

Subnet-router anycast address

à

Other anycast addresses (optional)

à

Loopback address (::1) of a loopback interface

Similarly, apart from these addresses, a router must always keep listening to the data

flow from the following multicast addresses.

à

Multicast addresses (FF01::1) of all the nodes within the node-local range

à

Multicast addresses (FF02::1) of all the nodes within the link-local range

à

Multicast addresses (FF02::2) of all the routers within the link-local range

à

Multicast addresses (FF05::2) of all the routers within the site-local range

à

Multicast address of the solicited-node (if the solicited-node group is added to an

interface of the router)

à

Multicast address of a multicast group (if any multicast group is added to an

interface of the router)

IPv6 Address Auto Configuration Technology

The state auto configuration employs the plug-and-play mode to insert a node into the

IPv6 network and starts it up without any manual interference. IPv6 has two different

mechanisms to shore up the plug-and-play network connection:

1-11

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link DSL-2750U Quick Start Manual preview
DSL-2750U
Brand: D-Link Pages: 2
D-Link DWR-112 Technical Support Setup Procedure preview
DWR-112
Brand: D-Link Pages: 11
D-Link DSR-250 Cli Reference Manual preview
DSR-250
Brand: D-Link Pages: 83
D-Link DSR-150 Reference Manual preview
DSR-150
Brand: D-Link Pages: 129
D-Link DSL-G804V Manual preview
DSL-G804V
Brand: D-Link Pages: 10
D-Link DSL-G804V Quick Information Manual preview
DSL-G804V
Brand: D-Link Pages: 21
D-Link DSL-2750E Quick Start Manual preview
DSL-2750E
Brand: D-Link Pages: 6
D-Link DSL-2750E Technical Support Setup Procedure preview
DSL-2750E
Brand: D-Link Pages: 17
D-Link DSL-2740U Setup Manual preview
DSL-2740U
Brand: D-Link Pages: 4
D-Link DSL-2730B How To Set Up preview
DSL-2730B
Brand: D-Link Pages: 6
D-Link DSL-520T Quick Installation Manual preview
DSL-520T
Brand: D-Link Pages: 86
D-Link DSL-502T Installing Usb Drivers preview
DSL-502T
Brand: D-Link Pages: 3
D-Link DSL-3900 Quick Start Manual preview
DSL-3900
Brand: D-Link Pages: 4
D-Link DWR-921 How To Set Up preview
DWR-921
Brand: D-Link Pages: 4
D-Link DSL-3580L Series Quick Installation Manual preview
DSL-3580L Series
Brand: D-Link Pages: 20
D-Link DSL-3785 Quick Installation Manual preview
DSL-3785
Brand: D-Link Pages: 64
D-Link DSL-224 User Manual preview
DSL-224
Brand: D-Link Pages: 73
3Com OfficeConnect 1600 Datasheet preview
OfficeConnect 1600
Brand: 3Com Pages: 8

Brands by name

Popular brands

Load more brands