manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 8

IS-ISv6 Configuration

Table of Contents

IS-ISv6 Overview .......................................................................................................8-1

Configuring IS-ISv6 ....................................................................................................8-2

Maintaining IS-ISv6 ..................................................................................................8-14

IS-ISv6 Configuration Examples ...............................................................................8-18

8.1 IS-ISv6 Overview

The Intermediate System-to-Intermediate System (

IS-IS

) protocol is a routing protocol

developed by the International Organization for Standardization (

ISO

) for CLNS. It is a

network layer protocol of the OSI protocol suite. It has been expanded to support IP

routing and form an integrated IS-IS protocol. The IS-IS protocol currently mentioned

refers to the integrated IS-IS protocol.

The IS-IS protocol is used as an Interior Gateway Protocol (

IGP

) in plenty of networks.

Its operating mechanism is similar to that of the OSPF protocol. It divides a network into

multiple areas. The routers in an area can manage only the routing information in the area.

This saves router costs and thus makes it suitable for large- and medium-scale networks.

The IS-IS protocol also uses Dijkstra's SPF algorithm to compute routes. It uses the SPF

algorithm to obtain the optimal route according to the link status database and then adds

the route to the IP routing table.

IS-IS is a routing protocol with high expansibility, so it can support the expansion of the

CLNS routing protocol to support IPv4 and support IPv6.

Uni-topology IS-IS can only run a single SPF algorithm. The topologies corresponding to

IPv4 and IPv6 must be identical and with special restriction. While the multi-topology IS-IS

can run multiple SPF algorithms. Then the topologies corresponding to IPv4 and IPv6 may

be different and with certain flexibility.

RFC 5308 (Routing IPv6 with IS-IS) defines how to use IS-IS to support IPv6. It defines

two new Tag, Length, Values (

TLV

s): IPv6 Reachability TLV and IPv6 Interface Address

TLV.

l

The TLV type value of the IPv6 Reachability TLV is 236 (0xEC). Its TLV effects are

equal to the two TLVs of IPv4: IP internally reachable and IP externally reachable.

Up/down and external are defined in this TLV and are used to indicate that routes are

redistributed mutually in the L2/L1 and to determine whether a route is an external

route.

8-1

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

ZETR 25 Installation Manual preview
25
Brand: ZETR Pages: 2
CallDirect CD Series At Command Manual preview
CD Series
Brand: CallDirect Pages: 33
Danfoss TFX Installation And Operation Manual preview
TFX
Brand: Danfoss Pages: 61
Lindy 25046 User Manual preview
25046
Brand: Lindy Pages: 4
B&B Electronics Parallel & Serial Port Checker PPC User Manual preview
Parallel & Serial Port Checker PPC
Brand: B&B Electronics Pages: 4
HMS Networks Anybus Communicator ABC4021 User Manual preview
Anybus Communicator ABC4021
Brand: HMS Networks Pages: 60
Ubiquiti AmpliFi AFi-G Quick Start Manual preview
AmpliFi AFi-G
Brand: Ubiquiti Pages: 20
AMG Systems AMG9240-C User Manual preview
AMG9240-C
Brand: AMG Systems Pages: 2
CalAmp Viper 100 User Manual preview
Viper 100
Brand: CalAmp Pages: 115
Broadband Products Xtreme Networked Boat User Manual preview
Xtreme Networked Boat
Brand: Broadband Products Pages: 16
Genexis FiberTwist XGS2420 Installation Manual preview
FiberTwist XGS2420
Brand: Genexis Pages: 7
Linksys WRT330N - Wireless-N Gigabit Gaming Router Wireless User Manual preview
WRT330N - Wireless-N Gigabit Gaming Router Wireless
Brand: Linksys Pages: 92
Billion BiPAC 7820NZ User Manual preview
BiPAC 7820NZ
Brand: Billion Pages: 100
Brother Network Card (Portuguese) Manual Do Utilizador preview
Network Card
Brand: Brother Pages: 251
Fujitsu FLASHWAVE 7500 Installation Manual preview
FLASHWAVE 7500
Brand: Fujitsu Pages: 392
Huawei NE-FIC-CE3 Specifications preview
NE-FIC-CE3
Brand: Huawei Pages: 1
Huawei OptiX RTN 910A Quick Installation Manual preview
OptiX RTN 910A
Brand: Huawei Pages: 26
Huawei Optix OSN 810 Quick Installation Manual preview
Optix OSN 810
Brand: Huawei Pages: 32

Brands by name

Popular brands

Load more brands