manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

l

The TLV type value of the IPv6 Interface Address TLV is 232 (0xE8). Its TLV effects

are equal to the TLV of IPv4: IP port address. The difference is that the original 32-bit

address segment is superseded by the 128-bit address segment in the new TLV.

l

The operating principles of IS-ISv6 are similar to those of IS-ISv4. For details, please

refer to "IS-IS Configuration" in IPv4 Routing Volume.

8.2 Configuring IS-ISv6

Configuring Basic Information

In this manual, it is assumed that the process-id is 0, and the VLAN100 interface is used.

To configure the basic information about IS-ISv6, perform the following steps:

Step

Command

Function

1

ZXR10(config)#

router isis

[

process-id

][

vrf

<

vrf-name

>]

Enables the IS-ISv6 routing

protocol process.

ZXR10(config-isis-0)#

system-id

<

system-id

>[

range

<

range-number

>]

Configures the system ID of a

route instance.

2

ZXR10(config-isis-0)#

area

<

area-address

>

Designates the area address

of IS-ISv6.

3

ZXR10(config-isis-0)#

interface

<

interface-name

>

Adds an interface to the

IS-ISv6 route entity.

4

ZXR10(config-isis-0-if-vlan100)#

ipv6 router isis

Runs the IS-ISv6 protocol on

an interface.

For a description of the parameters in Step 1, refer to the following table:

Parameter

Description

[

process-id

]

IS-IS process ID, range: 0-65535.

<

vrf-name

>

Specifies the VRF name, range: 1-32 characters.

For a description of the parameters in Step 2, refer to the following table:

Parameter

Description

<

system-id

>

Specifies the System ID of the instance, which is a

hexadecimal string of 6 bytes in the form of xxxx.xxxx.xxxx.

range

<

range-number

>

Specifies the extensible range of the System ID. The

value range is 0-32. The default value is 0. The instance

will assume an ID ranging from System ID to System

ID+<

range-number

>.

<

area-address

>

Specifies the area address, which is a hexadecimal string

of 1 to 13 bytes.

8-2

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

RuggedCom RUGGEDSWITCH RS900G Hardware Installation Manual preview
RUGGEDSWITCH RS900G
Brand: RuggedCom Pages: 23
Linksys NSLU2 - Network Storage Link NAS Server Quick Installation Manual preview
NSLU2 - Network Storage Link NAS Server
Brand: Linksys Pages: 64
TRENDnet TEW-733GR User Manual preview
TEW-733GR
Brand: TRENDnet Pages: 62
Orolia Seven Solutions WR-ZEN Series User Manual preview
Seven Solutions WR-ZEN Series
Brand: Orolia Pages: 167
NC-link NC-AP111 User Manual preview
NC-AP111
Brand: NC-link Pages: 20
B&B Electronics Elinx EIR508 Series Quick Start Manual preview
Elinx EIR508 Series
Brand: B&B Electronics Pages: 2
Symantec SV1800 Series Safety And Regulatory Compliance Manual preview
SV1800 Series
Brand: Symantec Pages: 100
Rasilient ApplianceStor 15MT User Manual preview
ApplianceStor 15MT
Brand: Rasilient Pages: 30
Comway 4G DTU Configuration Instructions preview
4G DTU
Brand: Comway Pages: 20
PairGain PG-Flex FLC-704 Manual preview
PG-Flex FLC-704
Brand: PairGain Pages: 20
Digi 9P 9360/9750 User Manual preview
9P 9360/9750
Brand: Digi Pages: 75
Optus Ultra WiFi Booster Quick Manual preview
Ultra WiFi Booster
Brand: Optus Pages: 8
rtd IDAN-ID5915 User Manual preview
IDAN-ID5915
Brand: rtd Pages: 28
Pro-Nets Technology Corporation WR750RL User Manual preview
WR750RL
Brand: Pro-Nets Technology Corporation Pages: 48
G&D DP1.2-Vision-IP-Fiber Installation And Operation Manual preview
DP1.2-Vision-IP-Fiber
Brand: G&D Pages: 240
Kasda KA1750 User Manual preview
KA1750
Brand: Kasda Pages: 44
TP-Link TL-R470T Plus Configuration Manual preview
TL-R470T Plus
Brand: TP-Link Pages: 182
Zte MF971R Quick Start Manual preview
MF971R
Brand: Zte Pages: 28

Brands by name

Popular brands

Load more brands