manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 8 IS-ISv6 Configuration

IPv6 address as well as the commands

ip router isis

and

ipv6 router isis

. Here, the

multi-topology environment is taken as an example.

3.

Enable the IS-ISv6 protocol on the interfaces.

4.

Check and verify the configuration results:

Neighbors are correctly established

between the routers, and each router correctly computes the IPv6 topology and can

successfully ping the loopback interface of the peer router.

Configuration Commands

S1 configuration:

S1(config)#interface vlan10

S1(config-if-vlan10)#ipv6 enable

S1(config-if-vlan10)#ipv6 address

3611::11/64

S1(config-if-vlan10)#exit

S1(config)#interface loopback5

S1(config-if-vlan10)#ipv6 enable

S1(config-if-vlan10)#ipv6 address

3555::52/64

S1(config-if-vlan10)#exit

S1(config)#router isis

S1(config-isis-0)#area 47.0005

S1(config-isis-0)#system-id 0000.0000.0011

S1(config-isis-0)#metric-style wide

S1(config-isis-0)#interface vlan10

S1(config-isis-0-if-vlan10)#ipv6 router isis

S1(config-isis-0-if-vlan10)#exit

S1(config-isis-0)#interface loopback5

S1(config-isis-0-if-loopback5)#ipv6 router isis

S1(config-isis-0-if-loopback5)#exit

S1(config-isis-0)#address-family ipv6

S1(config-isis-0-af)#multi-topology

S1(config-isis-0-af)#end

S2 configuration:

S2(config)#interface vlan10

S2(config-if-vlan10)#ipv6 enable

S2(config-if-vlan10)#ipv6 address

3611::10/64

S2(config-if-vlan10)#exit

S2(config)#interface loopback5

S2(config-if-loopback5)#ipv6 enable

S2(config-if-loopback5)#ipv6 address

3550::52/64

S2(config-if-loopback5)#exit

S2(config)#router isis

S2(config-isis-0)#area 47.0005

S2(config-isis-0)#system-id 0000.0000.0010

S1(config-isis-0)#metric-style wide

8-19

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

IBM E12 Quick Reference Manual preview
E12
Brand: IBM Pages: 4
Vonets MINI300 Quick Setting Manual preview
MINI300
Brand: Vonets Pages: 8
XNET INS2000 Install Manual preview
INS2000
Brand: XNET Pages: 17
Gbord EN-101 User Manual preview
EN-101
Brand: Gbord Pages: 8
ZyXEL Communications G-170S User Manual preview
G-170S
Brand: ZyXEL Communications Pages: 79
Federal Signal Corporation AR2000-M Installation And Maintenance Manual preview
AR2000-M
Brand: Federal Signal Corporation Pages: 49
3Com 3C433279A Release Note preview
3C433279A
Brand: 3Com Pages: 12
TP-Link TD-VG5612 Quick Installation Manual preview
TD-VG5612
Brand: TP-Link Pages: 2
Digisol DG-BG100 User Manual preview
DG-BG100
Brand: Digisol Pages: 81
Extron electronics Network Adapter AC AAP Specifications preview
Network Adapter AC AAP
Brand: Extron electronics Pages: 2
Teldat H2 RAIL Installation Manual preview
H2 RAIL
Brand: Teldat Pages: 47
TRENDnet TEG-S16R - DATA SHEETS Quick Installation Manual preview
TEG-S16R - DATA SHEETS
Brand: TRENDnet Pages: 12
National Instruments USB device 622x User Manual preview
USB device 622x
Brand: National Instruments Pages: 23
ASTRO U 960 Operating Manual preview
U 960
Brand: ASTRO Pages: 12
Billion Bipac 74 Series Instructions Manual preview
Bipac 74 Series
Brand: Billion Pages: 8
Ecos SECURE BOOT STICK FX Administrator'S Manual preview
SECURE BOOT STICK FX
Brand: Ecos Pages: 22
Cambium Networks PTP 850E Installation Manual preview
PTP 850E
Brand: Cambium Networks Pages: 99
Billion myGuard 7500GL User Manual preview
myGuard 7500GL
Brand: Billion Pages: 147

Brands by name

Popular brands

Load more brands