manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 2 NDP Configuration

Step

Command

Function

ZXR10(config-if-interface-name)#

ipv6 nd

prefix

<

ipv6-prefix

>

/

<

prefix-length

> [{<

valid-lifetime

>

<

preferred-lifetime

>} |

off-link

|

no-autoconfig

]

Sets the prefix option of the

router response packets sent

on the interface.

4

ZXR10(config-if-interface-name)#

no ipv6 nd prefix

<

ipv6-prefix

>

/

<

prefix-length

>

Clears the prefix option of the

router response packets sent

on the interface.

ZXR10(config-if-interface-name)#

ipv6 nd ra-interval

<

seconds

>

Specifies the interval for

sending router response

packets on the interface in the

unit of seconds. The value

range is 3-1800. The default

value is 600 seconds.

5

ZXR10(config-if-interface-name)#

no ipv6 nd

ra-interval

Restores the default

advertisement interval.

ZXR10(config-if-interface-name)#

ipv6 nd ra-lifetime

<

seconds

>

Specifies the value of the

ra-lifetime field in the router

response packets sent on the

interface in the unit of seconds.

The value range is 0-9000. The

default value is 1,800 seconds.

6

ZXR10(config-if-interface-name)#

no ipv6 nd

ra-lifetime

Restores the default value of

the ra-lifetime field.

ZXR10(config-if-interface-name)#

ipv6 nd

reachable-time

<

milliseconds

>

Specifies the time within

which the remote neighbor

is considered as reachable

after the reachability of the

remote neighbor is confirmed

in the unit of milliseconds.

The default value is 30,000

milliseconds.

7

ZXR10(config-if-interface-name)#

no ipv6 nd

reachable-time

Restores the default time.

ZXR10(config-if-interface-name)#

ipv6 nd

retransmit-time

<

milliseconds

>

Specifies the value of the

retransmit-time field in the

router response packets

in the unit of milliseconds.

The default value is 1,000

milliseconds.

8

ZXR10(config-if-interface-name)#

no ipv6 nd

retransmit-time

Restores the default value of

the retransmit-time field.

2-3

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

National Instruments NI 9229 Operating Instructions Manual preview
NI 9229
Brand: National Instruments Pages: 34
XMOS XC-2 Quick Start Manual preview
XC-2
Brand: XMOS Pages: 6
TP-Link Archer VR500vd Installation Manual preview
Archer VR500vd
Brand: TP-Link Pages: 7
Balluff Easy Tool-ID BSG TID-05-T30-00-005 Installation And Operation Manual preview
Easy Tool-ID BSG TID-05-T30-00-005
Brand: Balluff Pages: 46
MEMON memonizerWORKSTATION Quick Start Manual preview
memonizerWORKSTATION
Brand: MEMON Pages: 2
Paradyne Hotwire 8343 Installation Instructions Manual preview
Hotwire 8343
Brand: Paradyne Pages: 6
B&B Electronics Elinx EIR510 Series Quick Start Manual preview
Elinx EIR510 Series
Brand: B&B Electronics Pages: 2
Casablanca W-500 Technical Bulletin preview
W-500
Brand: Casablanca Pages: 13
Acorn Computers Limited A300 Series Quick Start Manual preview
A300 Series
Brand: Acorn Computers Limited Pages: 2
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
ExtraHop EDA 4200 Install preview
EDA 4200
Brand: ExtraHop Pages: 2
Vista VIPER H4 User Manual preview
VIPER H4
Brand: Vista Pages: 93
Alcatel-Lucent Broadband 700 MHz Brochure preview
Broadband 700 MHz
Brand: Alcatel-Lucent Pages: 8
Safety Vision ROADRECORDER 8400 NVR User Manual preview
ROADRECORDER 8400 NVR
Brand: Safety Vision Pages: 27
RadioLAN 140 MOBILINK User Manual preview
140 MOBILINK
Brand: RadioLAN Pages: 24
Junxion Junxion Box JB-110b User Manual preview
Junxion Box JB-110b
Brand: Junxion Pages: 48
Brother Network Card (Portuguese) Manual Do Utilizador preview
Network Card
Brand: Brother Pages: 251
IDT 89HPES12T3G2 Preliminary User'S Manual preview
89HPES12T3G2
Brand: IDT Pages: 146

Brands by name

Popular brands

Load more brands