manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

7.4.2 OSPFv3 Configuration Example 2

Configuration Description

As shown in

Figure 7-2

, S1 and S2 establish a link with each other via the direct connection

interfaces, S1 and S2 establish the link in area 0 whereas S2 and S3 establish a link

with each other in area 10 to advertise their respective loopback address route, and S1

redistributes the direct route.

Figure 7-2 OSPFv3 Configuration Example 2

Configuration Thought

1.

Enable the IPv6 protocol on the interfaces, configure IPv6 addresses for these

interfaces, configure loopback interfaces, enable IPv6 on the loopback interfaces,

and configure IPv6 addresses for the loopback interfaces.

2.

Configure OSPFv3.

3.

Add the interfaces to OSPFv3. S1 and S2 establish a link with each other in area 0,

S2 and S3 establish a link with each other in area 10, and S1 redistributes the direct

route.

4.

Check and verify the configuration results:

Neighbors are correctly established

between the routers, each router can learn the routes advertised by the other two

routers, and each router can ping the loopback interfaces of the other two routers.

Configuration Commands

S1 configuration:

S1(config)#interface vlan10

S1(config-if-vlan10)#ipv6 enable

S1(config-if-vlan10)#ipv6 address 3611::11/64

S1(config-if-vlan10)#exit

S1(config)#interface loopback5

S1(config-if-loopback5)#ipv6 enable

S1(config-if-loopback5)#ipv6 address 3555::52/64

7-16

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

Tripp Lite N201-005-BL Specification Sheet preview
N201-005-BL
Brand: Tripp Lite Pages: 3
VCS VideoJet 100 Manual preview
VideoJet 100
Brand: VCS Pages: 118
Lindsay Broadband LBON320AC Series Installation And Operation Manual preview
LBON320AC Series
Brand: Lindsay Broadband Pages: 4
Paradyne JetFusion 2100 Series User Manual preview
JetFusion 2100 Series
Brand: Paradyne Pages: 296
Top RAMS1000 User Manual preview
RAMS1000
Brand: Top Pages: 21
PaloAlto Networks ION 1000 Hardware Reference Manual preview
ION 1000
Brand: PaloAlto Networks Pages: 28
TP-Link TD-W8101G Quick Installation Manual preview
TD-W8101G
Brand: TP-Link Pages: 16
Xyclop XC-16CH-NVR-4TB Quick Start Manual preview
XC-16CH-NVR-4TB
Brand: Xyclop Pages: 19
Patton electronics 593/45 User Manual preview
593/45
Brand: Patton electronics Pages: 8
LevelOne WBA-4000 User Manual preview
WBA-4000
Brand: LevelOne Pages: 49
Accton Technology Cheetah EtherCard-2320 Quick Installation Manual preview
Cheetah EtherCard-2320
Brand: Accton Technology Pages: 10
C&H Technologies EM405D100 Specification Sheet preview
EM405D100
Brand: C&H Technologies Pages: 2
8e6 Technologies Threat Analysis Reporter TAR Quick Start Manual preview
Threat Analysis Reporter TAR
Brand: 8e6 Technologies Pages: 76
ZyXEL Communications WAP6804 User Manual preview
WAP6804
Brand: ZyXEL Communications Pages: 114
Patton electronics ForeFront 2616RC Getting Started Manual preview
ForeFront 2616RC
Brand: Patton electronics Pages: 80
MasterForce 241-0836 Operating Manual preview
241-0836
Brand: MasterForce Pages: 12
Renesas Temporary Target Board M38517T-ADS User Manual preview
Temporary Target Board M38517T-ADS
Brand: Renesas Pages: 14
Lanner ICS-I372 User Manual preview
ICS-I372
Brand: Lanner Pages: 80

Brands by name

Popular brands

Load more brands