manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 8 IS-ISv6 Configuration

Step

Command

Function

3.15

ZXR10(config-isis-0-if-vlan100)#

network

point-to-point

Enables a LAN network

interface to simulate a

point-to-point interface.

3.16

ZXR10(config-isis-0-if-vlan100)#

metric

<

value

>[

level-1

|

level-2

]

Configures IS-ISv6 metric

on an interface.

For a description of the parameters in Step 3.1, refer to the following table:

Parameter

Description

level-1

|

level-1-2

|

level-2-only

Specifies the circuit type of an interface. Either option must

be selected. By default, the circuit type of an interface is

level-1-2.

This is a basic parameter involved in IS-IS configuration to specify the operation type for

an interface. The default value is level-1-2. The value needs to match the IS-IS global

operation type. The settings of this parameter must also be matched between two routers

establishing adjacency.

For a description of the parameters in Step 3.2, refer to the following table:

Parameter

Description

<

interval

>

Specifies the interval at which the IS-ISv6 protocol sends

CSNP packets in the unit of seconds. The value range is

1-65535. The default value is 10 seconds for a broadcast link

and 3,600 seconds for a point-to-point link.

level-1

|

level-2

Specifies the applicable scope of the CSNP interval (level-1

CSNP or level-2 CSNP). By default, the interval takes effect

for both level-1 and level-2.

The above parameters specify the CSNP packet sending interval. When the optional

parameter is not carried in the command, the set interval takes effect for both level-1 CSNP

and level-2 CSNP on the interface.

For a description of the parameters in Step 3.3, refer to the following table:

Parameter

Description

<

interval

>

Specifies the interval at which the IS-ISv6 sends hello

packets on an interface in the unit of seconds. The value

range is 1-65535. The default value is 10 seconds.

level-1

|

level-2

Specifies the applicable scope of the hello interval (level-1

hello or level-2 hello). By default, the interval takes effect

for both level-1 and level-2.

8-11

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

E-Lins H900 Series User Manual preview
H900 Series
Brand: E-Lins Pages: 59
E-Lins H750 Quick Start Manual preview
H750
Brand: E-Lins Pages: 11
E-Lins H700 Series Quick Start Manual preview
H700 Series
Brand: E-Lins Pages: 9
E-Lins H685 Series Quick Start preview
H685 Series
Brand: E-Lins Pages: 5
e-Line Technology Network Video Recorders User Manual preview
Network Video Recorders
Brand: e-Line Technology Pages: 34
Dahua DHI-NVR2104-P-4KS2 Quick Start Manual preview
DHI-NVR2104-P-4KS2
Brand: Dahua Pages: 23
Tandberg Data Storagelibrary T24 Manual preview
Storagelibrary T24
Brand: Tandberg Data Pages: 28
NA DigiNet 416 User Manual preview
DigiNet 416
Brand: NA Pages: 22
Tbus NV-ER1816i Installation Manual preview
NV-ER1816i
Brand: Tbus Pages: 25
Faderfox 4midiloop User Manual preview
4midiloop
Brand: Faderfox Pages: 10
SAGEMCOM SE681 WiMAX User Manual preview
SE681 WiMAX
Brand: SAGEMCOM Pages: 75
Variscite VAR-EXT-CB105 Datasheet preview
VAR-EXT-CB105
Brand: Variscite Pages: 18
UfiSpace S9700-23D Hardware Installation Manual preview
S9700-23D
Brand: UfiSpace Pages: 32
Grundig GSS STC 160 Assembly Instruction Manual preview
GSS STC 160
Brand: Grundig Pages: 24
B-G Instruments DataPlot CB1224 Manual preview
DataPlot CB1224
Brand: B-G Instruments Pages: 4
ZyXEL Communications PK5000Z How To Configure preview
PK5000Z
Brand: ZyXEL Communications Pages: 3
National Instruments PXI Terminal Block NI TB-2709 Installation Manual preview
PXI Terminal Block NI TB-2709
Brand: National Instruments Pages: 12
Goobay 93122 User Manual preview
93122
Brand: Goobay Pages: 20

Brands by name

Popular brands

Load more brands