Zte ZXR10 5900E Series Configuration Manual Download Page 206

Page: 206 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

Step

Command

Function

ZXR10(config-dhcpv6)#

enable

Enables the embedded

DHCPv6 function.

ZXR10(config-dhcpv6)#

disable

Disables the DHCPv6 process.

ZXR10(config-dhcpv6)#

interface

interface-name

Enters DHCPv6 interface

configuration mode.

ZXR10(config-dhcpv6)#

server max-user

1-48000

Configures the maximum

number of users on the

DHCPv6 server.

ZXR10(config-dhcpv6)#

server single-user-quota

{[

addr

ess

max-address-number

[

prefix

max-prefix-number

>]}

Configures the maximum

number of addresses that can

be assigned to a DHCP client

and the maximum number of

associated address prefixes.

ZXR10(config-dhcpv6)#

server rapid-redial

Enables the sending of a

notification to the DHCP server

after a DHCPv6 client is

re-connected to the server and

has an address assigned.

ZXR10(config-dhcpv6-if)#

mode

{

server

relay

}

Enables DHCPv6 working

mode of an interface.

ZXR10(config)#

ipv6 addr-pool

pool-name

Enters IPv6 address pool

configuration mode.

ZXR10(config-ipv6-addr-pool)#

addr-range

start-ipv6

end-ipv6

vrf-instance

vrf-name

Configures the range of the

IPv6 address pool.

ZXR10(config-ipv6-addr-pool)#

exclude-range

start-ipv6

end-ipv6

vrf-instance

vrf-name

Configures IPv6 reserved

addresses.

ZXR10(config-ipv6-addr-pool)#

conflict-time

timeout

Configures the release time of

conflict addresses in the IPv6

address pool, the default value

is 30 minutes.

ZXR10(config-ipv6-addr-pool)#

lock

This locks the IPv6 address

pool. By default, the address

pool is not locked.

ZXR10(config-ipv6-addr-pool)#

threshold

percent

Configures the alarm threshold

of the IPv6 address pool, the

default threshold is 100%.

20-4

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands

Zte ZXR10 5900E Series, Configuration Manual

Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands