manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 13 IPv6 PIM-SM Configuration

Parameter

Description

<

access-list-name

>

Defines a group range in which the candidate RPs advertised

in BSR messages received are filtered.

13.3 IPv6 PIM-SM Maintenance and Diagnosis

The ZXR10 5900E provides the following commands to maintain IPv6 PIM-SM:

Command

Function

ZXR10(config)#

show ipv6 pim mroute

[

group

<

group-address

>][

source

<

source-address

>]

Displays the IPv6 PIM-SM routing

table.

ZXR10(config)#

show ipv6 mroute summary

Displays the routing table

information of the IPv6 broadcast

PIM-SM.

ZXR10(config)#

show ipv6 pim bsr

Displays the information of the

BSR.

ZXR10(config)#

show ipv6 pim rp mapping

Displays the RP mapping

information advertised by the

BSR.

ZXR10(config)#

show ipv6 pim rp hash

<

group-address

>

Displays the RP information

selected by a specific multicast

group.

ZXR10(config)#

show ipv6 pim interface

[<

interface-name

>]

Displays the interface on which

IPv6 PIM-SM is configured.

ZXR10(config)#

show ipv6 pim neighbor

[<

interface-name

>]

Displays the neighbor information

of a PIM-SM interface.

ZXR10(config)#

show ipv6 pim nexthop

Displays the PIM-SM next hop

information.

ZXR10#

show ipv6 pim traffic

[<

interface-name

>]

Displays the IPv6 PIM-SM traffic

statistics information.

ZXR10#

clear ipv6 pim traffic

Clears the IPv6 PIM-SM traffic

statistics information.

The command parameters are described as follows.

Parameter

Description

group

<

group-address

>

Multicast group address, in the X:X::X:X format

source

<

source-address

>

Source address, in the X:X::X:X format

<

interface-name

>

Interface name

13-9

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

Cambium Networks PTP 550 Series Quick Start Manual preview
PTP 550 Series
Brand: Cambium Networks Pages: 68
Cambium Networks PTP 820S Installation Manual preview
PTP 820S
Brand: Cambium Networks Pages: 110
iDirect iQ Desktop+ Installation, Support, And Maintenance Manual preview
iQ Desktop+
Brand: iDirect Pages: 52
Clavister NetWall W20A Getting Started Manual preview
NetWall W20A
Brand: Clavister Pages: 89
H3C NSQ1GT48EA0 Manual preview
NSQ1GT48EA0
Brand: H3C Pages: 3
XYZ Machine Tools TRAK 2OP M11 Mill Safety, Installation, Maintenance, Service And Parts List preview
TRAK 2OP M11 Mill
Brand: XYZ Machine Tools Pages: 203
Valcom VIP-822A Quick Start Manual preview
VIP-822A
Brand: Valcom Pages: 4
Buffalo LinkStation Mini User Manual preview
LinkStation Mini
Brand: Buffalo Pages: 71
Juniper EX2500 Quick Start preview
EX2500
Brand: Juniper Pages: 2
Mellanox Technologies ConnectX-3 Pro MCX349A-XCCN User Manual preview
ConnectX-3 Pro MCX349A-XCCN
Brand: Mellanox Technologies Pages: 35
Ubiquiti EdgeRouter PoE ERPoe-5 Quick Start Manual preview
EdgeRouter PoE ERPoe-5
Brand: Ubiquiti Pages: 13
Buffalo BS-GS2008P Quick Setup Manual preview
BS-GS2008P
Brand: Buffalo Pages: 2
iNetVu Tachyon CI1300 Quick Start Manual preview
Tachyon CI1300
Brand: iNetVu Pages: 20
Alcatel-Lucent 9364 Installation And Commissioning Manual preview
9364
Brand: Alcatel-Lucent Pages: 60
SMC Networks SMC-EZ1026DT User Manual preview
SMC-EZ1026DT
Brand: SMC Networks Pages: 56
2N Telekomunikace ATEUS STARGATE User Manual preview
ATEUS STARGATE
Brand: 2N Telekomunikace Pages: 67
Zhone 6388-A2 User Manual preview
6388-A2
Brand: Zhone Pages: 53
NetBurner SBL2e User Manual preview
SBL2e
Brand: NetBurner Pages: 30

Brands by name

Popular brands

Load more brands