background image

Chapter 1 IPv6 Address Configuration

The host automatically uses the global address prefix obtained from routers and

its own interface ID to automatically configure a global address to communicate

with other hosts within the Internet.

1.2 Configuring IPv6 Addresses

To configure IPv6 addresses, perform the following steps:

Step

Command

Function

1

ZXR10(config)#

interface

<

interface-name

>

Enters the interface

configuration mode.

ZXR10(config-if-interface-name)#

ipv6 enable

Enables the IPv6 protocol.

ZXR10(config-if-interface-name)#

ipv6 address

<

ipv6-address

>

/

<

prefix-length

>[{

eui-64

|

anycast

}]

Configures an IPv6 address on

an interface.

ZXR10(config-if-interface-name)#

ipv6 address

link-local

<

X:X::X:X

>

Configures the IPv6 link local

address of the interface.

2

ZXR10(config-if-interface-name)#

ipv6 mtu

<

bytes

>

Sets the

MTU

of the IPv6

packets to be transmitted on

the interface.

For a description of the parameters in Step 2, refer to the following table:

Parameter

Description

<

ipv6-address

>

Specifies the address to be configured on the interface. The

address format follows RFC 2373. 16 bits form a group and

groups are separated by colons. The address may also

assume the simplified mode as defined in RFC 2373.

<

prefix-length

>

Specifies the prefix length of the IPv6 address in decimal

system, indicating the number of consecutive most significant

bits that form the prefix in the IPv6 address.

eui-64

EUI-64 address.

anycast

Anycast address identifier.

<

bytes

>

Specifies the MTU value in the unit of bytes. The default

value depends on the specific interface type. The minimum

value is 1,280 bytes, and the value range is 1280-9202.

1.3 Maintaining IPv6 Addresses

To maintain IPv6 addresses, run the following commands:

1-13

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews: