manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

Command Output

Description

multicast-group FF02::9

Indicates that the multicast address used by the RIPng is

FF02::9.

administrative distance is 120

Indicates that the administrative distance of RIPng routes

is 120.

default metric is 1

Indicates that the default metric of RIPng routes is 1.

updates every 30 seconds, expire

after 180 seconds

garbage collect after 120 seconds

Indicates that the update timer currently set is 30s, the

timeout timer is 180s, and the garbage timer is 120s.

connect ripng route 0

Indicates that the number of connect RIPng routes is 0.

aggregate ripng route 0

Indicates that the number of aggregate RIPng routes is 0.

Redistribution

Indicates that the protocol type of rouet redistribute.

The following example shows the outputs of the command

show ipv6 rip database

:

ZXR10(config)#show ipv6 rip database

2010::/64

nexthop: 2010::13, via: vlan10

metric:

1, tag: 0 time: 00:01

The outputs of the command

show ipv6 rip database

are described as follows:

Command Output

Description

2010::/64

Indicates the destination network segment.

nexthop: 2010::13

Indicates the next-hop address. In this example, there is no

next hop because the network segment is a direct connection

segment.

via: vlan10

Indicates the egress interface of the route.

metric: 1, tag: 0

Indicates that the metric of the route is 1 and the tag is 0.

time: 00:01

Indicates the time of the route exist.

The following example shows the outputs of the command

show ipv6 rip interface

[<

interf

ace-name

>]:

ZXR10(config)#show ipv6 rip interface vlan10

vlan10: interface is up

RIPng is enabled

Split horizon enabled

Poison reverse enable

IPv6 interface address:

2010::13/64

The outputs of the command

show ipv6 rip interface

[<

interface-name

>] are described as

follows:

6-8

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link Verizon DSL-2750B Setup Manual preview
Verizon DSL-2750B
Brand: D-Link Pages: 6
D-Link DIR-857 Quick Installation Manual preview
DIR-857
Brand: D-Link Pages: 10
D-Link DSL-2740U Quick Installation Manual preview
DSL-2740U
Brand: D-Link Pages: 38
Parker H Series Installation & Service Instructions Manual preview
H Series
Brand: Parker Pages: 344
B&B Electronics Elinx EIRP305-T User Manual preview
Elinx EIRP305-T
Brand: B&B Electronics Pages: 19
Zonet ZEW1505 Quick Installation Manual preview
ZEW1505
Brand: Zonet Pages: 10
Samsung NAS Series Hardware User Manual preview
NAS Series
Brand: Samsung Pages: 65
Lorex LNR100 SERIES Instruction Manual preview
LNR100 SERIES
Brand: Lorex Pages: 186
Black Box JPM083A Manual preview
JPM083A
Brand: Black Box Pages: 9
H3C S10500 Series Mpls Configuration Manual preview
S10500 Series
Brand: H3C Pages: 400
Intellinet 523318 Instructions preview
523318
Brand: Intellinet Pages: 2
EnGenius ETR9360 Quick Start Manual preview
ETR9360
Brand: EnGenius Pages: 3
ADTRAN NetVanta 873 Specifications preview
NetVanta 873
Brand: ADTRAN Pages: 2
Sans Digital ELITENAS EN104L+(B) Quick Installation Manual preview
ELITENAS EN104L+(B)
Brand: Sans Digital Pages: 9
LaCie 301300U - Ethernet Disk NAS Server User Manual preview
301300U - Ethernet Disk NAS Server
Brand: LaCie Pages: 62
Quantum QWCM Installation Manual preview
QWCM
Brand: Quantum Pages: 7
AOpen ISDN SOHO Router User Manual preview
ISDN SOHO Router
Brand: AOpen Pages: 89
Amit CDD531AM-U02 User Manual preview
CDD531AM-U02
Brand: Amit Pages: 75

Brands by name

Popular brands

Load more brands