manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

Step

Command

Function

ZXR10(config-ospfv3-process-id-if-interface-

name)#

hello-interval

<

interval

>

Specifies the interval of

sending Hello packets on an

interface in the unit of seconds.

The value range is 1-65535.

The default value for

point-to-point and broadcast

interfaces is 10 seconds.

The default value for

non-broadcast and

point-to-multipoint interfaces is

30 seconds.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

retransmit-interval

<

interval

>

Specifies the time interval at

which an interface retransmits

an LSA in the unit of seconds.

The value range is 1-65535.

The default value is 5 seconds.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

transmit-delay

<

interval

>

Specifies the delay after which

an interface transmits a link

state update packet in the unit

of seconds. The value range

is 1-65535. The default value

is 1 second.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

dead-interval

<

interval

>

Specifies the aging time of

neighbors on an interface in

the unit of seconds. The value

range is 1-65535.

The default value for

point-to-point and broadcast

interfaces is 40 seconds.

The default value for

non-broadcast and

point-to-multipoint interfaces is

120 seconds.

ZXR10(config-ospfv3-process-id-if-interface-

name)#

cost

<

cost-value

>

Sets the interface cost value in

the unit of seconds. The value

range is 1-65535. The default

value of a loopback interface is

1, and that of other interfaces

is 10.

3

7-6

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link ShareCenter DNS-320L Datasheet preview
ShareCenter DNS-320L
Brand: D-Link Pages: 4
D-Link Verizon DSL-2750B Connection Instructions preview
Verizon DSL-2750B
Brand: D-Link Pages: 2
D-Link DVA-2800 Quick Start Manual preview
DVA-2800
Brand: D-Link Pages: 4
Paradyne 3172 Quick Reference preview
3172
Brand: Paradyne Pages: 20
Paradyne Compshere 3000 Series Notice preview
Compshere 3000 Series
Brand: Paradyne Pages: 2
Pantech Sprint PX-500 Quick Start Manual preview
Sprint PX-500
Brand: Pantech Pages: 17
Watchguard Firebox SOHO 6 Wireless Instructions Manual preview
Firebox SOHO 6 Wireless
Brand: Watchguard Pages: 8
Q-See QC814 Specifications preview
QC814
Brand: Q-See Pages: 2
TP-Link TD-8817 Specifications preview
TD-8817
Brand: TP-Link Pages: 3
Teac HD-35NAS User Manual preview
HD-35NAS
Brand: Teac Pages: 20
Maple Systems cMT-FHDX Series Installation Instruction preview
cMT-FHDX Series
Brand: Maple Systems Pages: 2
NETGEAR Powerline 100 Installation Manual preview
Powerline 100
Brand: NETGEAR Pages: 2
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
XtendLan XL-IPM401 User Manual preview
XL-IPM401
Brand: XtendLan Pages: 21
Ariesys AMK Series User'S Reference Manual preview
AMK Series
Brand: Ariesys Pages: 10
Sun Microsystems McDATA Eclipse 1620 Release Notes preview
McDATA Eclipse 1620
Brand: Sun Microsystems Pages: 9
Carrier 40VMW005 Installation And Maintenance Instructions Manual preview
40VMW005
Brand: Carrier Pages: 18

Brands by name

Popular brands

Load more brands