manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

For a description of the parameters in Step 2.5, refer to the following table:

Parameter

Description

level-1

|

level-2-only

|

level-1-2

Specifies the level of the configured router. By default, a

router is a level-1-2 router.

This is a basic parameter involved in IS-IS configuration. It is used to define the operation

type of the router according to the practical networking condition. By default, IS-IS-enabled

router is identified as a level-1-2 router.

For a description of the parameters in Step 2.6, refer to the following table:

Parameter

Description

<

interval

>

Specifies the periodic LSP refresh interval in the unit of

seconds. The value range is 1-65535. The default value is

900 seconds.

Set the LSP refresh interval of the IS-IS protocol so that the LSP packets locally generated

are periodically updated when the network is stable. By default, LSP packets are refreshed

at an interval of 900 seconds.

For a description of the parameters in Step 2.7, refer to the following table:

Parameter

Description

<

interval

>

Specifies the maximum LSP lifetime in the unit of seconds.

The value range is 1-65535. The default value is 1,200

seconds.

Set the maximum LSP lifetime of the local IS-IS, that is, the lifetime of LSP packets locally

generated in the databases of all the reachable nodes. By default, the maximum lifetime

of LSP packets is 1,200 seconds.

For a description of the parameters in Step 2.8, refer to the following table:

Parameter

Description

narrow

|

wide

Specifies the metric type (narrow or wide).

The narrow mode uses only 6 bits to carry the metric value,

whereas the wide mode uses 24 bits to carry it and supports

more TLVs to be carried.

The metric range in the narrow mode is smaller than that in the wide mode. In addition, the

wide mode supports more TLV extensions. By default, the metric-style is set to "narrow".

Topology creation may fail due to inconsistent settings of the metric-type between the two

routers to be interconnected.

For a description of the parameters in Step 2.9, refer to the following table:

8-6

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

Panasonic BB-HGW700A - Network Camera Router Installation/Troubleshooting Manual preview
BB-HGW700A - Network Camera Router
Brand: Panasonic Pages: 10
Lantronix SISPM1040-582-LRT Quick Start Manual preview
SISPM1040-582-LRT
Brand: Lantronix Pages: 2
Lantronix SDS1101 Quick Start Manual preview
SDS1101
Brand: Lantronix Pages: 7
Lantronix Maestro E220 Series Quick Start Manual preview
Maestro E220 Series
Brand: Lantronix Pages: 25
Vivotek FE9181-H Quick Installation Manual preview
FE9181-H
Brand: Vivotek Pages: 170
MikroTik RouterBOARD Groove Quick Setup Manual And Warranty Information preview
RouterBOARD Groove
Brand: MikroTik Pages: 4
National Instruments FieldPoint cFP-RTD-122 Operating Instructions Manual preview
FieldPoint cFP-RTD-122
Brand: National Instruments Pages: 15
TVT Digital TD-3316B4-16P-A1 Quick Start Manual preview
TD-3316B4-16P-A1
Brand: TVT Digital Pages: 2
Xantech CC12 Installation Instructions preview
CC12
Brand: Xantech Pages: 4
Juniper E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010 Manual preview
E SERIES BROADBAND SERVICES ROUTERS 11.3.X - ERX MODULE GUIDE REV 27-9-2010
Brand: Juniper Pages: 122
ZyXEL Communications VMG5313-BXB SERIES Quick Start Manual preview
VMG5313-BXB SERIES
Brand: ZyXEL Communications Pages: 2
Ubiquiti PowerBeam PBE-5AC-400-ISO Quick Start Manual preview
PowerBeam PBE-5AC-400-ISO
Brand: Ubiquiti Pages: 23
iNetVu Tachyon CI1300 Quick Start Manual preview
Tachyon CI1300
Brand: iNetVu Pages: 20
Addonics Technologies Network Adapter ADZIFCF Installation Manual preview
Network Adapter ADZIFCF
Brand: Addonics Technologies Pages: 1
Juniper TX MATRIX Hardware Manual preview
TX MATRIX
Brand: Juniper Pages: 396
Tripp Lite P581-006 Specification Sheet preview
P581-006
Brand: Tripp Lite Pages: 2
Garderos R-3700 Series Operating Manual preview
R-3700 Series
Brand: Garderos Pages: 21
e+p OCH 110 Installation Manual preview
OCH 110
Brand: e+p Pages: 2

Brands by name

Popular brands

Load more brands