Zte ZXR10 5900E Series Configuration Manual Download Page 152

Page: 152 / 226

ZXR10 5900E Series Configuration Guide (IPv6)

Step

Command

Function

ZXR10(config-mcast-igmp-if-interface-name)#

join-g

roup

group-address

Configures members for the

static group on the

IGMP

interface.

To delete all members from

the static group on the

interface, run the

form of

this command.

ZXR10(config-mcast-igmp-if-interface-name)#

join-group

group-address

Deletes the static group

member from the interface.

For a description of the parameters in Step 1, refer to the following table:

Parameter

Description

access-list-number

Standard IP access list name, with 1-31 characters

For a description of the parameters in Step 2, refer to the following table:

Parameter

Description

group-address

Static MLD join group address, in the X:X::X:X format

source-address

Source address, in the X:X::X:X format

For a description of the parameters in Step 3, refer to the following table:

Parameter

Description

access-list-number

Standard IP access list name, with 1-31 characters

By default, when a device receives an MLD leaving message, the group member will leave

the group if it does not receive any report message within (last member query interval *

2 + 1) seconds. If no option is configured in the command, it takes effect in all multicast

groups.

Configuring MLD Timers

After MLD is enabled on interfaces of multicast routers in a shared segment, an optimal

interface will be elected as the querier of the segment to obtain group member information

by sending query messages.

After sending a query message, the querier waits for a period to receive the report

messages from member hosts. The period is the value of the maximum response time

contained in the query messages. By default, the period is 10 seconds.

After receiving the query message, a member host in the segment will subtract a random

value on the basis of the maximum response time. It uses the result as its response time.

If the querier receives a report message from another member host during this period,

the host cancels to send a report message. If the querier does not receive any report

12-4

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands

Zte ZXR10 5900E Series, Configuration Manual

Search results

Summary of Contents for ZXR10 5900E Series

Reviews:

Related manuals for ZXR10 5900E Series

Brands by name

Popular brands