manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 20 DHCPv6 Configuration

Parameter

Description

<

threshold

>

Alarm threshold of the IPv6 address pool. Range: 50-100,

default: 100.

For a description of the parameters in Step 6, refer to the following table:

Parameter

Description

<

valid-lifetime

>

The valid life time of the address pool, in the unit of second,

in the range of 60-4294967295

<

preferred-lifetime

>

The preferred life time of the address pool, in the unit of

second, in the range of 60-4294967295

<

server-number

>

DNS server number, value 1 or 2

<

Tunnel endpoint name

>

Domain name. Range: 1–32 characters.

Configuring a DHCPv6 Relay

To configure a DHCPv6 relay on the ZXR10 5900E, perform the following steps:

Step

Command

Function

1

ZXR10(config)#

dhcp ipv6

Enters DHCPv6 configuration

mode.

ZXR10(config-dhcpv6)#

enable

Enables the embedded

DHCPv6 function.

2

ZXR10(config-dhcpv6)#

disable

Disables the embedded

DHCPv6 function.

ZXR10(config-dhcpv6)#

relay server group

<

number

>

Enters DHCPv6 relay server

group configuration mode from

DHCPv6 configuration mode.

ZXR10(config-dhcpv6)#

relay max-user

<

1-48000

>

Configures the maximum

number of users on the DHCP

relay.

ZXR10(config-dhcpv6r-server-group)#

algorithm

{

normal

|

first

|

round-robin

}

Configures the DHCPv6 relay

server to use a policy. The

default forwarding mode is

normal.

ZXR10(config-dhcpv6-server-group)#

server

<

server-no

><

server-ipv6

>[

interface

<

interface-name

>][

master

][

dscp

<

0-63

>]

Configures the DHCPv6 relay

server to trust information.

ZXR10(config-dhcpv6r-server-group)#

deadtime

<

time

>

Configures the unavailable

duration after the DHCPv6

relay server fails sending.

3

20-7

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

ICP DAS USA ZT-2510 Series Quick Start Manual preview
ZT-2510 Series
Brand: ICP DAS USA Pages: 8
LaCie d2 Network 2 Quick Install Manual preview
d2 Network 2
Brand: LaCie Pages: 44
LaCie LaCie Ethernet Disk Datasheet preview
LaCie Ethernet Disk
Brand: LaCie Pages: 2
LaCie 5big - Network NAS Server Quick Start Manual preview
5big - Network NAS Server
Brand: LaCie Pages: 9
LaCie 2big NAS Quick Install Manual preview
2big NAS
Brand: LaCie Pages: 14
LaCie 12big Rack Fibre 8 Quick Install Manual preview
12big Rack Fibre 8
Brand: LaCie Pages: 9
TC Electronic DB6 User Manual preview
DB6
Brand: TC Electronic Pages: 174
WAGO 852-1417 Operating And Assembly Instructions preview
852-1417
Brand: WAGO Pages: 2
F5 i5000 Series Platform Manual preview
i5000 Series
Brand: F5 Pages: 72
Conceptronic C150BRS4 Quick Installation Manual preview
C150BRS4
Brand: Conceptronic Pages: 230
Hirschmann OCTOPUS 5TX-EEC Description And Operating Instructions preview
OCTOPUS 5TX-EEC
Brand: Hirschmann Pages: 6
Lanner ICS-P570 User Manual preview
ICS-P570
Brand: Lanner Pages: 63
Kanguru Data Bank User Manual preview
Data Bank
Brand: Kanguru Pages: 13
NETGEAR WGR614 - Wireless-G Router Wireless Reference Manual preview
WGR614 - Wireless-G Router Wireless
Brand: NETGEAR Pages: 116
LaCie 301297U - 1TB Ethernet Disk XP Embedded Network Attached... Online Manual preview
301297U - 1TB Ethernet Disk XP Embedded Network Attached...
Brand: LaCie Pages: 67
Teldat G1N Installation Manual preview
G1N
Brand: Teldat Pages: 23
Ubiquiti EdgeRouter X Quick Start Manual preview
EdgeRouter X
Brand: Ubiquiti Pages: 20
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20

Brands by name

Popular brands

Load more brands