manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

Step

Command

Function

ZXR10(config-dhcpv6-pool)#

preference

<

preference-value

>

Configures the server

preference. The range of

the preference is 1-255.

ZXR10(config-dhcpv6-pool)#

aftr address

<

ipv6-address

>[

option-code-value

<

option_code

>]

Configures the aftr address.

Range: 1-65535

ZXR10(config-dhcpv6-pool)#

aftr fqdn

<

Tunnel endpoint

name

>[

option-code-value

<

option_code

>]

Configures the aftr domain

name. Range: 1-65535.

ZXR10(config-dhcpv6-pool)#

server-unicast-address

<

ipv6-address

>

Configures the unicast address

of the server.

ZXR10(config-dhcpv6)#

policy

<

policy-name

><

priority

>

Enters DHCPv6 policy

configuration mode from

DHCPv6 configuration mode

and configures the priority of

the policy. The range of the

priority is 1-5.

ZXR10(config-dhcpv6-policy)#

dhcpv6-pool

<

pool-name

>

This binds a DHCPv6 policy to

a DHCPv6 address pool.

7

ZXR10(config-dhcpv6-policy)#

link-addrss

<

ipv6-address

>

Configures a DHCPv6 policy

link-address.

ZXR10(config-dhcpv6)#

interface

<

interface-name

>

Enters DHCPv6 interface

configuration mode.

ZXR10(config-dhcpv6-if)#

server policy

<

policy-name

>

Configures a DHCPv6 server

policy on the interface.

ZXR10(config-dhcpv6-if)#

enable server-unicast

Enables unicast on a DHCPv6

interface.

8

ZXR10(config-dhcpv6-if)#

dscp

<

0-63

>

Configures the IPv6 Traffic

Class option carried in the

message replied from the

DHCP server to DHCP relay.

For a description of the parameters in Step 4, refer to the following table:

Parameter

Description

<

start-ipv6

>

The start IP address of the IPv6 address pool.

<

end-ipv6

>

The end IP address of the IPv6 address pool.

vrf-instance

<

vrf-name

>

IPv6 address pool in the VRF instance.

<

timeout

>

The time before releasing conflicted addresses for the IPv6

address pool. Range: 1-18000 minutes, default: 30 minutes.

20-6

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

Salto Node Installation Manual preview
Node
Brand: Salto Pages: 2
DCE ANS-205 User Manual preview
ANS-205
Brand: DCE Pages: 5
Allied Telesis AT-9424Ts/XP AC Datasheet preview
AT-9424Ts/XP AC
Brand: Allied Telesis Pages: 3
KEMP Technologies LoadMaster 1500 Installation And Configuration Manual preview
LoadMaster 1500
Brand: KEMP Technologies Pages: 71
IBM BladeCenter Management Module Installation And User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 184
CalAmp Viper 100 User Manual preview
Viper 100
Brand: CalAmp Pages: 115
Ubiquiti PBE-M5-400-ISO Quick Start Manual preview
PBE-M5-400-ISO
Brand: Ubiquiti Pages: 28
Digisol DG-BG100 User Manual preview
DG-BG100
Brand: Digisol Pages: 81
Planet IPOE-171-60W User Manual preview
IPOE-171-60W
Brand: Planet Pages: 20
PairGain HiGain Line Unit HLU-388 Quick Installation Manual preview
HiGain Line Unit HLU-388
Brand: PairGain Pages: 7
AIC HA201-AP User Manual preview
HA201-AP
Brand: AIC Pages: 64
Multitech ROUTE FINDER RFIPSC-1 Quick Start Manual preview
ROUTE FINDER RFIPSC-1
Brand: Multitech Pages: 54
Juniper EX8200 Series Brochure preview
EX8200 Series
Brand: Juniper Pages: 12
Encore Networks EN-1000 Quick Installation Manual preview
EN-1000
Brand: Encore Networks Pages: 2
D-Link DIR-X5460 Quick Installation Manual preview
DIR-X5460
Brand: D-Link Pages: 2
Tripp Lite N302-006 Specification Sheet preview
N302-006
Brand: Tripp Lite Pages: 2
Bosch GKF 10.8V-8 Professional Manual preview
GKF 10.8V-8 Professional
Brand: Bosch Pages: 20
Bosch RA1141 Operating/Safety Instructions Manual preview
RA1141
Brand: Bosch Pages: 103

Brands by name

Popular brands

Load more brands