manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

You can set interfaces as passive interfaces. When an interface is set as a passive

interface, its address information will be carried only in local LSP packets but the interface

will not send packets.

For a description of the parameters in Step 2.16, refer to the following table:

Parameter

Description

dynamic

Indicates that the system name is dynamically obtained.

For a description of the parameters in Step 4.1, refer to the following table:

Parameter

Description

<

1-255

>

Specifies the distance. The value range is 1-255. The default

value is 115.

The administrative distance of an IS-ISv5 route is used for IPv6 route computation. The

smaller the value, the better the IS-ISv6 route is than the routes obtained by other routing

means or other routing protocols.

For a description of the parameters in Step 4.3, refer to the following table:

Parameter

Description

<

protocol

>

Specifies the route origin, which can be "connect", "static",

"rip", "ospf", or "bgp". This parameter is mandatory. To

redistribute IS-IS/OSPF routes, it is necessary to specify the

instance number.

level-1

|

level-2

|

level-1-2

Specifies the redistribution range. The default value is

"level-2".

metric

<

metric-value

>

Specifies the metric value of the redistributed route. The

value range is 0-4261412864. The default value is 10.

route-map

<

map-tag

>

Specifies the route map name for the current protocol

redistribution, which is a string of 1 to 31 characters.

If the metric-style is narrow, the value range of <

metric-value

> is 0-63. If the metric-style is

wide, the value range of <

metric-value

> is 0-426142864.

For a description of the parameters in Step 4.5, refer to the following table:

Parameter

Description

X:X::X:X/

<

0-128

>

Specifies the IPv6 network segment prefix.

8-8

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Link DSL-2750U Quick Start Manual preview
DSL-2750U
Brand: D-Link Pages: 2
Magnadyne RV2458 User Manual preview
RV2458
Brand: Magnadyne Pages: 13
Watchguard Firebox SOHO 6 Wireless Instructions Manual preview
Firebox SOHO 6 Wireless
Brand: Watchguard Pages: 8
Watchguard XTM 5 Series Hardware Manual preview
XTM 5 Series
Brand: Watchguard Pages: 24
IBM J02M Quick Start Manual preview
J02M
Brand: IBM Pages: 32
Jetter JetWeb JX2-PR0FI1 Operator'S Manual preview
JetWeb JX2-PR0FI1
Brand: Jetter Pages: 67
HELVAR Imagine 920 Installation Manual preview
Imagine 920
Brand: HELVAR Pages: 2
WAGO 852-1411 Operating And Assembly Instructions preview
852-1411
Brand: WAGO Pages: 2
HGST Ultrastar Serv24 S2122-N24-4 Installation Manual preview
Ultrastar Serv24 S2122-N24-4
Brand: HGST Pages: 36
Aewin Technologies SCB-9651 User Manual preview
SCB-9651
Brand: Aewin Technologies Pages: 86
Leviton IPHS5-1LW Product Bulletin preview
IPHS5-1LW
Brand: Leviton Pages: 4
Paradyne JetFusion 2100 Series User Manual preview
JetFusion 2100 Series
Brand: Paradyne Pages: 296
Ubiquiti EdgeRouter ER-8 Quick Start Manual preview
EdgeRouter ER-8
Brand: Ubiquiti Pages: 20
ZyXEL Communications POE-12 Specifications preview
POE-12
Brand: ZyXEL Communications Pages: 2
MCT MPU100ZW User Manual preview
MPU100ZW
Brand: MCT Pages: 12
DayTronic PC-HSICA Instruction Manual preview
PC-HSICA
Brand: DayTronic Pages: 13
Variscite VAR-SOM-MX6 HEAT PLATE KIT Quick Start Manual preview
VAR-SOM-MX6 HEAT PLATE KIT
Brand: Variscite Pages: 3
IBM 32R1860 - Nortel Layer 2/3 Copper GbE Switch... User Manual preview
32R1860 - Nortel Layer 2/3 Copper GbE Switch...
Brand: IBM Pages: 14

Brands by name

Popular brands

Load more brands