manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual, Page: 39 / 226

Share
Download
Zte ZXR10 5900E Series Configuration Manual Download Page 39

Chapter 3 IPv6 Tunnel Configuration

Step

Command

Function

6

ZXR10(config-ipv6-tunnel-if-v6_tunnel1)#

tunnel

destination ipv4

<

ipv4-address

>

Specifies the destination

address of the tunnel. To

delete the destination address

configuration of the tunnel, use

the

no

of the command.

Configuring 6to4 Tunnel

To configure a 6to4 tunnel, perform the following steps:

Step

Command

Function

1

ZXR10(config)#

interface v6_tunnel1

<

tunnel_no

>

Creates an IPv6 tunnel

interface. To delete the tunnel

interface, use the

no

format of

the command.

The parameter <

tunnel_no

>

indicates the tunnel number.

The number of tunnel interfaces

that can be created ranges

from 1 to 512.

2

ZXR10(config)#

ipv6-tunnel-config

Enters the IPv6 tunnel

configuration mode.

3

ZXR10(config-ipv6-tunnel)#

interface v6_tunnel

<

tunne

l_no

>

Enters the IPv6 tunnel interface

configuration mode.

4

ZXR10(config-ipv6-tunnel-if-v6_tunnel1)#

tunnel

mode ipv6ip 6to4

Sets the current tunnel mode

to 6to4. To cancel the current

tunnel mode, use the

no

format

of the command.

5

ZXR10(config-ipv6-tunnel-if-v6_tunnel1)#

tunnel

source ipv4

<

src_address

>

Specifies the source address

of the tunnel. To delete the

source address configuration

of the tunnel, use the

no

format

of the command.

3-5

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments