manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 10

IPv6 QoS Configuration

Table of Contents

IPv6 QoS Overview ..................................................................................................10-1

Configuring IPv6 QoS...............................................................................................10-1

IPv6 QoS Configuration Examples ...........................................................................10-1

10.1 IPv6 QoS Overview

IPv6 QoS is added with IPv6 support in addition to the functions of IPv4 QoS. For details

about QoS, refer to the section about the general description and principles of QoS in the

QoS Volume.

10.2 Configuring IPv6 QoS

The commands for configuring IPv6 QoS are similar to those for configuring IPv4 QoS,

except that IPv6 addresses are involved during the configuration. For details about the

configuration commands, refer to the section about QoS configuration in the QoS Volume.

10.3 IPv6 QoS Configuration Examples

l

Configuration Description

As shown in

Figure 10-1

, user1 accesses the system via the interface gei-0/1/1/1

whereas user2 accesses the system via the interface gei-0/1/1/2. The DSCP values

are 1 and 2 respectively. Packets are sent via the interface gei-0/1/1/3.

According to the requirements, the DSCP values of the packets of the two users sent

via the interface gei-0/1/1/3 should be 7, the guaranteed bandwidth should be 100 M,

and the maximum bandwidth should be 150 M.

10-1

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

Panasonic WJ-NV200K Quick Reference Manual preview
WJ-NV200K
Brand: Panasonic Pages: 4
3xLogic V250 Quick Start Manual preview
V250
Brand: 3xLogic Pages: 2
8e6 Technologies Enterprise Filter Authentication R3000 Quick Start Manual preview
Enterprise Filter Authentication R3000
Brand: 8e6 Technologies Pages: 66
Idis DR-4100P Series Installation Manual preview
DR-4100P Series
Brand: Idis Pages: 30
LaCie d2 Network 2 Quick Install Manual preview
d2 Network 2
Brand: LaCie Pages: 44
LaCie LaCie Ethernet Disk Datasheet preview
LaCie Ethernet Disk
Brand: LaCie Pages: 2
LaCie 5big - Network NAS Server Quick Start Manual preview
5big - Network NAS Server
Brand: LaCie Pages: 9
LaCie 2big NAS Quick Install Manual preview
2big NAS
Brand: LaCie Pages: 14
LaCie 12big Rack Fibre 8 Quick Install Manual preview
12big Rack Fibre 8
Brand: LaCie Pages: 9
Enterasys X-Pedition 2000 Getting Started Manual preview
X-Pedition 2000
Brand: Enterasys Pages: 86
Ruckus Wireless ZoneFlex 7731 Getting Started Manual preview
ZoneFlex 7731
Brand: Ruckus Wireless Pages: 56
AOpen 4-Port 10/100Mbps Ethernet Broadband Router User Manual preview
4-Port 10/100Mbps Ethernet Broadband Router
Brand: AOpen Pages: 41
Rosewill RC-402 User Manual preview
RC-402
Brand: Rosewill Pages: 3
Buffalo LinkStation Quick Setup Manual preview
LinkStation
Brand: Buffalo Pages: 2
BHU NETWORKS BXM2 User Manual preview
BXM2
Brand: BHU NETWORKS Pages: 75
Hama 00176547 Operating Instruction preview
00176547
Brand: Hama Pages: 25
Infoblox Infoblox-250 Installation Manual preview
Infoblox-250
Brand: Infoblox Pages: 16
CNC-Step AceroDURO 100/S100 Operating Instructions Manual preview
AceroDURO 100/S100
Brand: CNC-Step Pages: 86

Brands by name

Popular brands

Load more brands