manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 3 IPv6 Tunnel Configuration

S1(config-if-v6_tunnel2)#ipv6 address 2002:0101:0101::1/64

S1(config-if-v6_tunnel2)#ipv6 enable

S1(config-if-v6_tunnel2)#!

S1(config)#ipv6-tunnel-config

S1(config-ipv6-tunnel)#interface v6_tunnel2

S1(config-ipv6-tunnel-if-v6_tunnel2)#tunnel mode ipv6ip 6to4

S1(c config-ipv6-tunnel-if-v6_tunnel2)#tunnel source ipv4 1.1.1.1

S1(config-ipv6-tunnel-if-v6_tunnel2)#!

S1(config)#ipv6 route 2002::/16 v6_tunnel2

S2 configuration:

S2(config)#interface v6_tunnel2

S2(config-if-v6_tunnel2)#ipv6 address 2002:0101:0102::1/64

S2(config-if-v6_tunnel2)#ipv6 enable

S2(config-if-v6_tunnel2)#!

S2(config)#ipv6-tunnel-config

S2(config-ipv6-tunnel)#interface v6_tunnel2

S2(config-ipv6-tunnel-if-v6_tunnel2)#tunnel mode ipv6ip 6to4

S2(config-ipv6-tunnel-if-v6_tunnel2)#tunnel source ipv4 1.1.1.1

S2(config-ipv6-tunnel-if-v6_tunnel2)#!

S2(config)#ipv6 route 2002::/16 v6_tunnel2

Configuration Verification

Check the tunnel configurations on S1 and verify whether the configurations have taken

effect:

S1(config)#show running-config-interface v6_tunnel2

! <INTERFACE>

interface v6_tunnel2

index 1348

ipv6 enable

ipv6 address 2002:101:101::1/48

!

! </INTERFACE>

! <V6_TUNNEL>

ipv6-tunnel-config

interface v6_tunnel2

tunnel mode ipv6ip 6to4

tunnel source ipv4 1.1.1.1

! </V6_TUNNEL>

S1(config)#show ipv6 interface brief

v6_tunnel2

[up/up]

fe80::2d0:d0ff:fe52:abcf

2002:101:101::1/64

3-9

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

National Instruments NI 9871 Operating Instructions Manual preview
NI 9871
Brand: National Instruments Pages: 24
National Instruments NI 9478 Operating Instructions Manual preview
NI 9478
Brand: National Instruments Pages: 32
National Instruments FIELDPOINT FP-1600 Operating Instructions Manual preview
FIELDPOINT FP-1600
Brand: National Instruments Pages: 8
Garland INT40G2SR44 User Manual preview
INT40G2SR44
Brand: Garland Pages: 43
IBM 8677 - BladeCenter Rack-mountable - Power Supply Planning And Installation Manual preview
8677 - BladeCenter Rack-mountable - Power Supply
Brand: IBM Pages: 126
XtendLan XL-HCW224C User Manual preview
XL-HCW224C
Brand: XtendLan Pages: 52
Dataprobe iBoot Instruction Manual preview
iBoot
Brand: Dataprobe Pages: 16
Edimax GS-5208PLG V2 Quick Installation Manual preview
GS-5208PLG V2
Brand: Edimax Pages: 15
Edge-Core ES3510 Installation Manual preview
ES3510
Brand: Edge-Core Pages: 64
Patton ipRocketLink 3101 Series Getting Started Manual preview
ipRocketLink 3101 Series
Brand: Patton Pages: 119
Transition Networks N-FXE-xxx-01 User Manual preview
N-FXE-xxx-01
Brand: Transition Networks Pages: 5
Tripp Lite N002-025-RD Specification Sheet preview
N002-025-RD
Brand: Tripp Lite Pages: 3
Comtrend Corporation AR-5319 User Manual preview
AR-5319
Brand: Comtrend Corporation Pages: 208
Dynamix DV-24 User Manual preview
DV-24
Brand: Dynamix Pages: 87
Allied Telesis AR440S Hardware Reference Manual preview
AR440S
Brand: Allied Telesis Pages: 44
Tripp Lite B078-001-USB Specification preview
B078-001-USB
Brand: Tripp Lite Pages: 2
TP-Link VIGI Quick Start Manual preview
VIGI
Brand: TP-Link Pages: 2
Fibrain FSR-RG1 User Manual preview
FSR-RG1
Brand: Fibrain Pages: 20

Brands by name

Popular brands

Load more brands