manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

ZXR10 5900E Series Configuration Guide (IPv6)

9.3 Maintaining BGP4+

Common Maintenance Commands for Viewing Information

Certain debugging commands can be used to locate and remove BGP route faults. The

show

command is most commonly used and can be run on a router to show the current

BGP neighbors and the BGP routes learned by the router.

To maintain BGP, run the following commands:

Command

Function

ZXR10(config)#

show ip bgp protocol

Shows configuration information

about the BGP protocol module.

ZXR10(config)#

show bgp ipv6 unicast neighbor

Shows BGP adjacency and the

current neighbor status.

ZXR10(config)#

show bgp ipv6 unicast

Shows the entries in the BGP

routing table.

ZXR10(config)#

show BGP ipv6 unicast summary

Shows the states of all BGP

neighbors.

The following is a sample output from the

show ip bgp protocol

command:

E1#show ip bgp protocol

BGP router ID is 1.1.1.11, Local as is 100

Hold time is 180 seconds, KeepAlive time is 60 seconds

Default local preference is 100

Default export metric is 0

IPv4 IGP synchronization is disabled

IPv6 IGP synchronization is disabled

Default information advertise is disabled

Always compare med is disabled

Fast fallover is enabled

Client-to-client reflection is enabled

Enforce-first-as is enabled

IPv4 client-number: 1

IPv4 unicast is activated

BGP FRR is disabled

BGP IPv6 frr is disabled

Router target is filtered

Graceful restart is disabled

As-path ignore is disabled

Router-id ignore is disabled

BGP advertise-active-only is disabled

BGP VPNv4 advertise-active-only is disabled

BGP IPv4 rib-only is disabled

9-2

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

D-Linke DHP-346AV Quick Installation Manual preview
DHP-346AV
Brand: D-Linke Pages: 32
Hama 53107 Operating Instruction preview
53107
Brand: Hama Pages: 10
REXROTH efc series Instruction Manual preview
efc series
Brand: REXROTH Pages: 68
Qixiang Technology QR310 Installation And Configuration Quick Manual preview
QR310
Brand: Qixiang Technology Pages: 16
ZyXEL Communications P-660W-T1 v2 User Manual preview
P-660W-T1 v2
Brand: ZyXEL Communications Pages: 244
Selta Alyseo 106 User Manual preview
Alyseo 106
Brand: Selta Pages: 83
Cabletron Systems MMAC-Plus 9G536-04 User Manual preview
MMAC-Plus 9G536-04
Brand: Cabletron Systems Pages: 42
Xantech IR-X10 Installation Instructions Manual preview
IR-X10
Brand: Xantech Pages: 16
Raven RFMOW V2 User Manual preview
RFMOW V2
Brand: Raven Pages: 33
Atlantis WebShare 141 WN Quick Start Manual preview
WebShare 141 WN
Brand: Atlantis Pages: 78
Microchip Technology PD-9501-10GCO/AC User'S Installation Manual preview
PD-9501-10GCO/AC
Brand: Microchip Technology Pages: 41
M86 Security IR Web Filter User Manual preview
IR Web Filter
Brand: M86 Security Pages: 540
Billion Bipac 74 Series Instructions Manual preview
Bipac 74 Series
Brand: Billion Pages: 8
Billion BiPAC 7404VGO Specifications preview
BiPAC 7404VGO
Brand: Billion Pages: 2
Riverbed SteelCentral AppResponse 2170 Installation Manual preview
SteelCentral AppResponse 2170
Brand: Riverbed Pages: 166
Ringdale Thin Twinax Terminal LM-6488 Installation And Setup Manual preview
Thin Twinax Terminal LM-6488
Brand: Ringdale Pages: 15
Cambium Networks PTP 820C User Manual preview
PTP 820C
Brand: Cambium Networks Pages: 672
Billion BiPAC 7401VGP User Manual preview
BiPAC 7401VGP
Brand: Billion Pages: 121

Brands by name

Popular brands

Load more brands