manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 8 IS-ISv6 Configuration

division is helpful to decrease the demand for memory, and the routers in each area only

need to maintain a smaller link state database.

Figure 8-2

shows a multi-area IS-IS instance. S1 is in Area 1, S2 in Area 0, and S3 and

S4 in Area 2. On S1, perform route aggregation for the network segments in Area 1. The

direct routes are redistributed to the IS-IS on R4.

Figure 8-2 Multi-Area IS-ISv6 Configuration Example

Configuration Thought

1.

Enable the IPv6 protocol on the interfaces, configure IPv6 addresses for these

interfaces, configure loopback interfaces, enable IPv6 on the loopback interfaces,

and configure IPv6 addresses for the loopback interfaces.

2.

Configure the IS-ISv6 protocol and ensure that the system-ids of the routers are not

the same. Establish L2 neighbors between S2 and S1/S3, and establish L1 neighbors

between S3 and S4. Here, the multi-topology environment is taken as an example.

3.

Enable the IS-ISv6 protocol on the interfaces.

4.

Enable route aggregation on S1.

5.

Redistribute the direct route on S4.

6.

Check and verify the configuration results:

The routers can correctly establish

neighbors and correctly compute the IPv6 topology, and the interface addresses of

the routers can be successfully pinged from each other

Configuration Commands

S1 configuration:

S1(config)#interface vlan10

S1(config-if-vlan10)#ipv6 enable

S1(config-if-vlan10)#ipv6 address 2003::1/64

S1(config-if-vlan10)#exit

S1(config)#interface loopback1

S1(config-if-loopback1)#ipv6 enable

S1(config-if-loopback1)#ipv6 address 2000:0:0:1::1/64

S1(config-if-loopback1)#exit

8-23

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

DBM ACE9600 Operating Manual preview
ACE9600
Brand: DBM Pages: 50
NETGEAR AC1450 Installation Manual preview
AC1450
Brand: NETGEAR Pages: 14
H3C CR1606-F Installation Instructions Manual preview
CR1606-F
Brand: H3C Pages: 12
Moxa Technologies TAP-125 Series User Manual preview
TAP-125 Series
Brand: Moxa Technologies Pages: 51
Intel IXP45X Developer'S Manual preview
IXP45X
Brand: Intel Pages: 958
Supero SUPERSERVER 6027TR-H71FRF User Manual preview
SUPERSERVER 6027TR-H71FRF
Brand: Supero Pages: 118
Ubiquiti PBE-M5-400-ISO Quick Start Manual preview
PBE-M5-400-ISO
Brand: Ubiquiti Pages: 28
Quidway S3000-EI Series Operation Manual preview
S3000-EI Series
Brand: Quidway Pages: 16
Wieland wienet UMS 5-L Installation Instruction preview
wienet UMS 5-L
Brand: Wieland Pages: 2
Quantum MC300 Prism User Manual preview
MC300 Prism
Brand: Quantum Pages: 140
Billion BiPAC 7560G Quick Start Manual preview
BiPAC 7560G
Brand: Billion Pages: 12
LOOQS MeeBox Router Review preview
MeeBox Router
Brand: LOOQS Pages: 13
RadioLabs O2Wind Instruction preview
O2Wind
Brand: RadioLabs Pages: 11
Crestron C2N-NPA8 Operation Manual preview
C2N-NPA8
Brand: Crestron Pages: 40
D-Link DES-1008FX User Manual preview
DES-1008FX
Brand: D-Link Pages: 37
Crestron DigitalMedia DM-RPP-K24 Manual preview
DigitalMedia DM-RPP-K24
Brand: Crestron Pages: 2
D-Link DIR-880L Quick Installation Manual preview
DIR-880L
Brand: D-Link Pages: 32
Zte MF283+ User Manual preview
MF283+
Brand: Zte Pages: 28

Brands by name

Popular brands

Load more brands