manualshive.com logo in svg

Zte ZXR10 5900E Series, Configuration Manual

The Zte ZXR10 5900E Series is a powerful network switch designed for seamless connectivity. With its advanced features and impressive performance, this product is a must-have for any business or home network setup. Enhance your networking experience with the included Instructions Manual, available for free download at manualshive.com.

Share
Download
background image

Chapter 9 BGP4+ Configuration

BGP IPv6 rib-only is disabled

Route dampening is disabled

Distance : external 20 internal 200

RT constraint filter is enabled

Number of all peer : 8

Number of enabled peer : 8

Number of disabled peer : 0

Number of establised peer : 1

Number of actived ipv4 peer : 2

Number of actived ipv6 peer : 5

Number of actived vpnv4 peer : 1

Number of actived ipv4_multi peer : 0

For a description of the sample output from the

show ip bgp protocol

command, refer to

the following table:

Command Output

Description

Hold time is 180 seconds, KeepAlive

time is 60 seconds

Indicates that the hold time is 90 seconds and the keepalive

time is 30 seconds.

Default local preference is 100

Indicates that the default local preference is 100.

IPv4 IGP synchronization is disabled

BGP routing table is synchronized with IPv4 IGP routing table

(by default, they are not synchronized).

IPv6 IGP synchronization is disabled

BGP routing table is not synchronized with IPv6 IGP routing

table (by default, they are not synchronized).

Default export metric is 0

Indicates the default export metric is 0.

Distance : external 20 internal 200

Indicates that the external administrative distance is 20 and

the internal administrative distance is 200.

The following is a sample output from the

show bgp ipv6 unicast neighbor

command:

ZXR10#show BGP ipv6 unicast neighbor

BGP neighbor is 2002:9::2, remote AS 300, external link

BGP version 4, remote router ID 218.231.0.1

BGP state = Established, up for 00:13:58

Last read update 00:13:58, hold time is 90 seconds, keepalive interval is 30

seconds

Neighbor capabilities:

Route refresh: advertised and received

New ASN Capability: advertised

Address family IPv4 Unicast: received

IPv4 MPLS Label capability: received

Address family IPv4 Multicast: received

Address family VPNv4 Unicast: received

Address family IPv6 Unicast: advertised and received

IPv6 MPLS Label capability: received

9-3

SJ-20150114102049-011|2015-01-15 (R1.0)

ZTE Proprietary and Confidential

Summary of Contents for ZXR10 5900E Series



































































































































































































































Reviews:

No comments

Related manuals for ZXR10 5900E Series

NEC N8104-213 Instructions Manual preview
N8104-213
Brand: NEC Pages: 8
H3C S5120V3-EI Series Manual preview
S5120V3-EI Series
Brand: H3C Pages: 54
H3C CR16000-M Installation Manual preview
CR16000-M
Brand: H3C Pages: 116
IBM BladeCenter Management Module Installation And User Manual preview
BladeCenter Management Module
Brand: IBM Pages: 184
Balluff BIC 1I12-P2A25-M30MI1-BPX05-110 User Manual preview
BIC 1I12-P2A25-M30MI1-BPX05-110
Brand: Balluff Pages: 12
Kasda LinkSmart KW6515 User Manual preview
LinkSmart KW6515
Brand: Kasda Pages: 31
LGC wireless InterReach Fusion SingleStar Installation And Operation Manual preview
InterReach Fusion SingleStar
Brand: LGC wireless Pages: 154
Ubiquiti EdgeRouter 12 Quick Start Manual preview
EdgeRouter 12
Brand: Ubiquiti Pages: 23
TP-Link Deco XE200 User Manual preview
Deco XE200
Brand: TP-Link Pages: 57
Zoom Realtek Series User Manual preview
Realtek Series
Brand: Zoom Pages: 31
Comtrend Corporation WAP-5922MP Quick Install Manual preview
WAP-5922MP
Brand: Comtrend Corporation Pages: 4
Linksys PLK300 Quick Installation Manual preview
PLK300
Brand: Linksys Pages: 6
MaxComm M-150 Manual preview
M-150
Brand: MaxComm Pages: 10
LUX LUMEN 10230 Manual preview
10230
Brand: LUX LUMEN Pages: 41
Billion BiPAC 5200S RC Series User Manual preview
BiPAC 5200S RC Series
Brand: Billion Pages: 79
Korenix JetNet 5720G-8P Series Quick Installation Manual preview
JetNet 5720G-8P Series
Brand: Korenix Pages: 52
Axis M31-L SERIES Installation Manual preview
M31-L SERIES
Brand: Axis Pages: 30
National Instruments USB device 622x User Manual preview
USB device 622x
Brand: National Instruments Pages: 23

Brands by name

Popular brands

Load more brands