Zhone ETHX-2214-DS3 Installation Instructions Manual Download

Page: 1 / 28

ETHX-2214-DS3 and ETHX-2224-DS3
EtherXtend DS3 Ethernet Access Device
Installation Instructions

Document Number ETH3-A2-ZN10-10

Issue 2 - August 2008

Contents

Software and Firmware License Agreement ..................................................... 2

Introduction to ETHX-2214-DS3 and ETHX-2224-DS3 .................................... 4

Package Contents ............................................................................................. 6

Release Notes ................................................................................................... 6

Product Documentation Online ......................................................................... 6

Powering Up the Network Extender .................................................................. 7

Connecting the DS3 Lines................................................................................. 9

Connecting the Ethernet Lines ........................................................................ 11

LED Indicators ................................................................................................. 12

Web Interface .................................................................................................. 14

Command Line Interface ................................................................................. 19

Resetting the Network Extender to Factory Defaults ...................................... 21

Specifications .................................................................................................. 23

Safety Notices ................................................................................................. 24

EMI Notices ..................................................................................................... 24

NEBS Compliance ........................................................................................... 24

Service and Repair .......................................................................................... 25

Important Safety Instructions........................................................................... 26

Summary of Contents for ETHX-2214-DS3




























Search results

Summary of Contents for ETHX-2214-DS3

Reviews:

Related manuals for ETHX-2214-DS3

Brands by name

Popular brands

Zhone ETHX-2214-DS3, Installation Instructions Manual

Search results

Summary of Contents for ETHX-2214-DS3

Reviews:

Related manuals for ETHX-2214-DS3

Brands by name

Popular brands