Wfly ET Series Instruction Manual Download

Page: 75 / 131

Throttle mixing

Mixing

Status

AIL to THR

ELE to THR

RUD to THR

INH

Mode

Switch

Center

- -

1/2

Throttle mixing

Mixing

Rate 1

AIL to THR

ELE to THR

RUD to THR

+0 %

Rate 2

+0%

2/2

Interface path: WFLY → [Model Menu] → [Throttle Mixing]

This function is used to correct the eﬀect of the swash on the engine when operating the aileron or

elevator. In addition, there is a certain correction eﬀect on the torque of the left/right rotation when the
spinning.

Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching by

switch to perform function setting separately.

When the mixing control switch is set to [--], the swash
mixing only works under the selected ﬂight conditions.

Mixing ACT and INH options.

Left mixing, default 0%,range -100%~+100%

Right mixing, default 0%,range -100%~+100%

Center trimming mode: Correct only near the center.
Linear trimming mode: Linear correction of the entire range.

Application example

Aileron to throttle: When the aileron is operated, the engine is corrected by the decrease in the number of

load revolutions. The number of engine revolutions can be adjusted by setting the ratios 1 and 2 (left
aileron, right aileron) independently.

After using [Throttle Mixes], the throttle servo will become larger. Therefore, set the limit for the servo

end point (adjust in the [End Point ] interface).

075

Model Menu\Helicopter

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands