Wfly ET Series Instruction Manual Download

Page: 115 / 131

Camber Flap To Ele

Status

Switch

Camber ﬂap to ElE

INH

- -

ELE

Rate1

Rate2

Function status switch (INH, ON, default [INH])

Control switch assignment, default [--]

Diﬀerent aircraft types will have diﬀerent wings

Adjust in positive and negative directions, range ±120%,
default 0%

Interface path: WFLY → [Model Menu] → [Camber Flap to ElE]

When using ﬂaps, the pitch angle of the model has a tendency to change. This mixing compensates for

the attitude change of the model by combining the inputs of the elevator.

The ratio of the upper and lower directions of the elevator can be adjusted. If the mixing direction is

reversed due to a connection problem, you can also make adjustments by changing the polarity of the ratio.

In ﬂight, this function can be switched on or oﬀ with the switch (set to [ - ] if it is always on, or [ - ], and the

position is "on" to achieve the function normally on.)

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition] to switch

through the switches and perform function settings separately.

Elevator

Elevator2(Aileron to Elevator)

Flaps

Flaps2

V-tail

115

Model Menu\Glider

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands