Wfly ET Series Instruction Manual Download

Page: 83 / 131

AIL Diﬀerential

Interface path: WFLY → [Model Menu] → [AIL Diﬀerential]

When the ailerons are controlled by two servos, the ratio of the upper and lower rudder angles of the left

and right ailerons can be independently adjusted.

*This function is only used on the two-wing models after the model is selected.

Aileron 2

Aileron

Flight conditions: Set the "Flight Condition" control switch in [Model Function] → [Condition]. Switching

is performed by switches, and function settings are made separately.

* When debugging, please operate the stick to the end point for maximum motion veriﬁcation to avoid

exceeding the range of the servo or the body.

AIL diﬀerential

AIL

AIL2

Left

Right

+100%

Set end point of each servo

Range0~120%, default 100%

083

Model Menu\Airplane

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands