Wfly ET Series Instruction Manual Download

Page: 96 / 131

Aileron to Camber Flap

Aileron to Camber

FLP

FLP2

Switch

Link

Left

Right

+0%

Status

INH

OFF

- -

Function status button (INH, ON, default [INH])

Function control switch (default [--])

Connect this mix to other mixes (default [oﬀ])

Interface path: WFLY → [Model Menu] → [Aileron to Camber Flap]

This mixing uses the aileron mode to operate the ﬂaps. When the aileron stick is operated, both the

aileron and the ﬂap operate simultaneously in the aileron mode, which can improve the characteristics of
the snap roll operation.

Adjust in positive and negative directions, range ±120%, default 0%

By setting the switch, mixing can be turned on during flight. If you want to keep it on, set it to [--

], you can also set it to [--], and the position is "On" to achieve the function normally open.

Step function: can connect this mix to other mixes.

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition].

Switching is performed by switches, and function settings are made separately.

Aileron

Aileron2

Flaps2

Flaps

096

Model Menu\Airplane

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands