Wfly ET Series Instruction Manual Download

Page: 90 / 131

Rudder to Elevator

Interface path: WFLY → [Model Menu] → [RUD to elevator]

This function is used to mix the elevator and rudder operation. Used to correct unexpected movement

trends when the rudder is used in a ﬂight such as a roll or side ﬂy.

●

This function can be used to control "on" / "oﬀ" with the switch during ﬂight. (If you want to keep it on, set

it to [--], you can also set it to [--], and the position is "On" to achieve the function normally open.)

● Step function: It can connect this mix to other mixes.
● Three types of curves can be set.

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching is

performed by switches, and function settings are made separately.

RUD to elevator

2/2

Switch

Link

Status

INH

- -

OFF

Function status switch

(

INH, ON, default [INH])

Function control switch (default [--])

Connect this mix to other mixes (default [oﬀ])

RUD to elevator

1/2

Oﬀset

Type

E X P 1

Rate B

Rate A

+100%

EXP B

EXP A

100%

+15 0

+1 0 0

+50

- 50

- 1 0 0

- 1 5 0

+150%

RAT E

+150%

PO S

Rudder

Elevator

Elevator2
Aileron elevator

090

Model Menu\Airplane

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands