Wfly ET Series Instruction Manual Download

Page: 123 / 131

Ailevator

Ailevator

ELE
AIL5

RUD
AIL

Down

+100%

ELE

Left

Ritht

AIL

Adjust the amount of
movement of the
elevator separately

Adjust the amount of action of the aileron action on the elevator. (Set to 0
if only the 2 servos of the elevator are used instead of the ailerons)

Interface path: WFLY → [Model Menu] → [Ailevator]

If the aileron type is selected in the model type selection function of the context menu and the aileron

type is selected in the tail type, the elevator of the aileron elevator tail type can be adjusted in this setting
interface. (Only for the body with one servo on each side of the elevator)

When operating the ailerons, let the elevator servo act as aileron to improve the performance of the

rolling shaft.

Elecvator

Elecvator2

Range ±120%

●

The amount of operation of each servo can be adjusted separately. (For the connection method of the

servo, please refer to "Servo connection of diﬀerent model categories")

● When the connection causes the mixing direction to be reversed, it can be adjusted by changing the

polarity (+/-) of the action amount.

● If the amount of motion is too large or the rudder is repeatedly ruddered, the servo may be

unresponsive. Be sure to conﬁrm the actual movement of the body when setting.

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching is

performed by switches, and function settings are made separately.

123

Model Menu\Glider

Summary of Contents for ET Series




































































































































Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands

Wfly ET Series, Instruction Manual

Search results

Summary of Contents for ET Series

Reviews:

Related manuals for ET Series

Brands by name

Popular brands