Wfly ET Series Instruction Manual Download | Manualshive

Page: 12 / 131

background image

Rotate 180° on the front

Up and down 90°

Switch conﬁguration and model types

The Travel Of Antenna Direction Adjustment

Power LED: Left, power indicator light, red
RF LED: Right, RF indicator light, blue.

POWER: Click one power key only for 3 seconds to open/shut down; Click 2 power keys at the same time

to ﬂash shutdown.

SA: Short lever 3 positions (user-deﬁned)
SB: Long lever 3 positions (user-deﬁned)
SC: Long lever 3 positions (user-deﬁned)
SD: Short lever 3 positions (user-deﬁned)

SE: Short lever 3 positions (user-deﬁned)
SF: Short lever 3 positions (user-deﬁned)
SG: Short lever 3 positions (user-deﬁned)

SH: Long lever momentary (user-deﬁned)
LS/RS: Slide lever (user-deﬁned)
VL/VR: Thumb wheel (user-deﬁned)
T1-T6: Trim (user-deﬁned)

5-way button: Move the cursor button up and down or left and right, middle button for conﬁrmation(Long

press for momentary)

Fn switch key: Click to switch for 5-way button working mode. Fn status LED lighting-oﬀ, 5-way button

works for interface operation setting and parameters input when touch screen is out of work(PS: 5-way
button and touch panel could be used at the same time). Fn status LED is on, 5-way button works as control

switch, click button or trimming.

PHONE: Earphone plug in the earphone transmitter speaker, meanwhile earphone output the voice.
TRAINER: Trainer port.

HOME/MON.: Home/Monitor key, short click home, long click monitor.
EXIT/LOCK: Exit/Lock key, short click to exist, long click to lock the screen.

The antenna activity of the transmitter is limited by the stroke. If the activity is exceeded, the antenna will

be damaged. The active travel indication of the antenna is as following:

Before Use

012

Mandatory

«
...
10
11
12
13
14
...
»

Summary of Contents for ET Series




































































































































Reviews:

No comments

Related manuals for ET Series

Brand: CAME Pages: 12

Brand: CAME Pages: 16

Brand: Ultrak Pages: 41

Brand: Zander Aachen Pages: 10

Brand: Samson Pages: 20

Brand: Bang & Olufsen Pages: 80

Brand: Bang & Olufsen Pages: 13

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

Brand: Kathrein Pages: 16

Brand: National Instruments Pages: 2

Brand: Eaton Pages: 96

Optidrive Elevator

Brand: Invertek Pages: 5

Brand: Techtrol Pages: 4

Brand: PS Automation Pages: 4

Brand: Festo Pages: 62

Brand: Hearth Products Controls Pages: 5

Brand: Carel Pages: 48

Controller CR100

Brand: Sonos Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands