Wfly ET Series Instruction Manual Download | Manualshive

Page: 87 / 131

background image

Idle down

Status

Switch

Oﬀset

0%

- -

INH

Idle Down

Interface path: WFLY → [Model Menu] → [Idle Down]

The idle down is usually used when landing. By operating a switch, the engine speed can be reduced.
This feature is only available when the throttle position is low.

The initial setting of the switch is [--], so ﬁrstly set the control switch (and the position of the switch).

Setup steps

1 Click the status button to enable the [Idle Down] function.
2 Click the switch button to assign the function switch and set the function open position of the switch.
3 Turn on the selected[Idle Down] control switch.
4 The engine stick is in the idle state and the rate is adjusted until the engine reaches the minimum

speed.

Please pay attention to the throttle connection here, do not let the servo exceed the stroke. (When set to

a negative rate, shift to the throttle high direction.)

* Flight conditions: Set the "Flight Condition" control switch in [Model Menu] → [Condition]. Switching is

performed by switches, and function settings are made separately.

The position of the throttle at "Idle Down”
Range:High[-100%], Low[+100%]
Default 0%

Function control switch, default [--]

087

Model Menu\Airplane

«
...
85
86
87
88
89
...
»

Summary of Contents for ET Series




































































































































Reviews:

No comments

Related manuals for ET Series

Brand: J4C Pages: 4

Brand: ABB Pages: 6

615 Series ANSI

Brand: ABB Pages: 60

Brand: T-Verter Pages: 121

Brand: Happy Pages: 10

Brand: Ebyte Pages: 34

Brand: YASKAWA Pages: 61

Brand: IBM Pages: 12

Brand: K&K Pages: 10

Brand: Eaton Pages: 6

Brand: CAME Pages: 18

Brand: CAME Pages: 28

Brand: CAME Pages: 28

Brand: CAME Pages: 4

Brand: CAME Pages: 40

Brand: CAME Pages: 26

Brand: CAME Pages: 34

Brand: CAME Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands