Wfly ET Series Instruction Manual Download | Manualshive

Page: 67 / 131

background image

Condition

7

4

6

8

3

3

5

2

4

1

Aileron

Elevator

Throttle

Gear

Rudder

AUX6

AUX5

AUX4

AUX2

AUX3

0

0

0

0

0

0

0

0

0

0

1/2

Channel

Channel

Delay

Delay

Model Menu\Helicopter

Condition

Condition

- -

- -

- -

- -

Delay

Idle 1

Idle 2

Idle 3

Hold

Normal

Interface path: WFLY → [Model Menu] → [Condition]
With this function, ﬂight conditions can be conﬁgured as needed, and there are 5 ﬂight conditions to

choose from.

If you do not need to use the conditional switching function, you do not have to set it on this page. The

default conﬁguration can be used directly.

When multiple ﬂight conditions are set, the priority between them is to prioritize the ﬁnal ﬂight conditions!
Delay: Avoid swaying of the fuselage caused by sudden changes in the position of the servo or the

unsynchronized action time between the passages when switching ﬂight conditions.

12 channels can be
individually set to delay

Assign control switch:

By default, there is no switch

assignment (--), click to enter the assignment interface.
Switching between ﬂight conditions can be performed using
switches such as a toggle switch, a stick, and a side lever.
Set the unwanted ﬂight condition switch to empty (--).

The delay value of each ﬂight
condition can be set separately.
By activating the control switch
set, the delay value of each
channel corresponding to the
ﬂight condition can be set.

Switch instruction

Rename:

If condition needs to

be modiﬁed, click on the name
bar on the left to directly rename
the operation. Press and hold
the 5-way button to reset the
default name.

Delay configuration
interface point

Condition

Logic

Mode

Logic

And

SwitchB

- -

SwitchA

- -

Single mode (single switch control).
Logic mode (combination switch control).
"AND" mode: The ﬂight conditions can be switched when

both switches are turned on.

"OR" mode: As long as one switch is turned on, the ﬂight

conditions can be switched.

XOR mode: When the positions of the two switches are

reversed, the ﬂight conditions can be switched.

* "On", "Oﬀ": When the switch is selected, the selected

position or location.

067

Servo Reverse

12

6

11

5

10

4

9

3

8

2

7

1 Aileron

Elevator

Throttle

Rudder

Gear

AUX6

AUX6

AUX5

AUX4

AUX3

AUX2

AUX1

Normal

Normal

Revers

Normal

Normal

Normal

Normal

Normal

Normal

Normal

Normal

Normal

«
...
65
66
67
68
69
...
»

Summary of Contents for ET Series




































































































































Reviews:

No comments

Related manuals for ET Series

Brand: Panasonic Pages: 15

Brand: Panasonic Pages: 42

Brand: UNITED Pages: 22

Brand: Fairchild Pages: 2

Brand: Fairford Pages: 233

Brand: Garmin Pages: 220

Brand: Gardena Pages: 16

Brand: Veeder-Root Pages: 27

Brand: Valve Concepts Pages: 18

Brand: K&K Pages: 6

Brand: Ublox Pages: 2

Brand: u-blox Pages: 19

Brand: Xantrex Pages: 56

Brand: Xantrex Pages: 2

Freedom Sequence

Brand: Xantrex Pages: 58

Brand: Xantrex Pages: 4

Brand: Xantrex Pages: 20

Brand: Auber Pages: 3

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands